Best Barns the Garden Shed Assembly Book Download Page 15 | Manualshive

Page: 15 / 24

background image

Gable Siding Rest

on Filler

3/4" Space

3.

Install another 29" filler board on the opposite corner.

61-3/4" Corner Trim

Step 16 Install Rear Roof Gable

Important: Bottom edge of the
siding extends over 1x4 trim.
Paint this edge.

1.

Install a gable on the rear wall. The gable siding will extend over

the 1x4 trim on the lower wall NOT behind the trim! and rest
on top of filler boards.

Step 15 Install Upper Back Wall Trim Continued

4.

Cut to fit a 61-3/4" long 1x4 trim board flush along top of wall frame.

5.

Install 61-3/4" long 1x4 corner trim flush with the siding on the

sidewalls at both corners.

2.

Secure gable to wall by nailing

through the gable plate with 10d
sinkers. Nail siding along the 1x4
trim board with 8d galv. nails.

«
...
13
14
15
16
17
...
»

Summary of Contents for the Garden Shed

























Reviews:

No comments

Related manuals for the Garden Shed

Brand: Palmako Pages: 40

Brand: Palmako Pages: 118

Brand: Solid Pages: 16

Brand: Palmako Pages: 105

Brand: Palmako Pages: 37

White Wood FRJ40-4030

Brand: Palmako Pages: 56

winchester arbour

Brand: Rowlinson Garden Products Pages: 2

Roger FR70-5656-2

Brand: Palmako Pages: 103

Roger FR44-5357-1

Brand: Palmako Pages: 102

Brand: SUKKAHMART Pages: 7

266H Wheel Horse 72052

Brand: Toro Pages: 40

Brand: Toro Pages: 40

265H Wheel Horse

Brand: Toro Pages: 40

Brand: Sentry Buildings Pages: 30

Jefferson 16x20 Building

Brand: Sentry Buildings Pages: 30

Palmako Roger FRE70-5656

Brand: Lemeks Pages: 103

Brand: G21 Pages: 40

Brand: Mercia Garden Products Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands