Best Barns the Garden Shed Assembly Book Download | Manualshive

Page: 7 / 24

background image

center line

Step 3

Assemble Roof Gables

1.

Butt (2) two 52-1/2" long 2x4s together and

secure by nailing a 3-1/2" x 44" long plywood
gusset across the top where they butt together.
Center the plywood gusset over the 2x4 plates.
Use glue and 6d common nails.

19" Gable Stud

6.

Repeat to assemble another gable. Remove 2x4 blocks.

2x4 Gable Plate

2.

Remove 2x4 blocks that secured collar tie in place in Step 1.

3.

Place (2) two 66" long 2x4 truss members at the top of the truss jig.

4.

Install the gable plate assembled above to the truss legs with 2-1/2" wood screws, see

detail 'B'. Install a 2x4 block to hold the plate straight. Secure the top 2x4s together with
a 1x4 barbed metal plate.

5.

Install 2x4 -19" gable studs. Nail through the bottom plate

with 10d sinkers and secure the top with 1x4 barbed metal
drive-on plates.

52-1/2" long 2x4

3/4" Plywood

Gusset

2x4 Block

Screw gable plate to truss

leg with 2-1/2" screw.

See Detail 'B'

DETAIL B

Barbed

Metal Plate

«
...
5
6
7
8
9
...
»

Summary of Contents for the Garden Shed

























Reviews:

No comments

Related manuals for the Garden Shed

Brand: X-METAL Pages: 34

Brand: Grosfillex Pages: 72

Brand: Palmako Pages: 31

Brand: Solid Build Pages: 12

Sunbrella Side Shade

Brand: Pergola kits USA Pages: 10

Brand: Solid Pages: 32

Brand: Select Pages: 38

ELEGANTO 2724 OLL

Brand: telluria Pages: 68

Pent Potting Shed

Brand: total sheds Pages: 12

Atlanta Chicken Coop

Brand: Little Cottage Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands