background image

If your door opening is out of square,
the space around the doors will not be
even. You can remove and reposition
the side trim to make allowances for
this. The side trim does not have to be
flush with the frame of the door opening.
You can move the trim in or out to make
the door spacing equal. Secure hinges
to door trim with 2" screws.

2x4 Door Stop

Barrel Bolt  on the

back of left door

2.

Install a sliding door latch on the left

door with 1" black screws provided.
Install the receiver on right side door.

Step 18 Install Doors & Hardware

1.

Before you fasten the hinges to the door trim, temporarily prop the doors in the opening.

Leave a space at the top of the doors and between the doors and the side trim to allow room
for the doors to expand when they absorb moisture.

Left Door

3.

Install a barrel bolt on the lower back of

the door to secure this door in place when
closed. You will need to drill a hole for
the round shaft to drop into.

4.

Install another barrel bolt at the top of the

door.

2x4 Door Stop

Install metal roof edging perimeter of the roof area. Install shingles according to the instructions
on the wrapper. If you need more detailed instructions on installing shingles, there are good
publications at book stores, newsstands or youtube.com.

Install Sliding Door Latch

Summary of Contents for BB-ELM1016

















Reviews: