Best Barns BB-ELM1016 Assembly Book Download

Page: 11 / 16

Repeat Steps 10 thru 12 to install

the gable on the front wall.

Remove 2x4 braces from front wall.

Install (1) one next to the 2x4
installed above.

Gather a 2x4 removed from the

pallet. Cut to fit and install next.

Repeat to install 2x4s on the opposite

side wall.

Step 12

Install Rear Gable Siding

Install gable siding on the back gable using 6d

galv. nails. The gable siding should extend no
more than 1/2" above the 2x4 frame and 1-1/2"
past gable ends.

Step 11

Install 'Z' Flashing

Step 13

Install 2x4 Truss Headers

Place a 72" long 2x4 on top of the siding on the sidewall. It will butt against the siding on the

rear gable. Nail this 2x4 to the 2x4 tie plate with 10d sinkers.

2x4-72" Board

Side Wall Siding

60" Long 'Z' Flashing

Roof Gable

Back Wall Siding

Install (2) two 60” pieces of 'Z' flashing
across the top of the siding on the end
wall siding. Secure in place using 6d galv.
nails spaced 12” apart. The ends will be
covered by corner trim.

1-1/2" Past End

of Gable

Summary of Contents for BB-ELM1016

















Search results

Summary of Contents for BB-ELM1016

Reviews:

Related manuals for BB-ELM1016

Brands by name

Popular brands

Best Barns BB-ELM1016, Assembly Book

Search results

Summary of Contents for BB-ELM1016

Reviews:

Related manuals for BB-ELM1016

Brands by name

Popular brands