Bernina activa 125 Owner'S Workbook Download Page 57 | Manualshive

Page: 57 / 92

background image

M

ASTERING

Y

OUR

BERNINA

®

1/10/02

activa

125/135 PE/145/

57

BERNINA

®

activa

125/135 PE/145

M

ASTERING

Y

OUR

BERNINA

®

ELASTIC THREAD IN THE BOBBIN

• A Black Latch bobbin case is suggested.
• Wind elastic thread on the bobbin.
• Place in bobbincase and adjust tension if necessary.
• All-purpose sewing thread is used in the needle.
• Select stitch #1 - SL 4mm to 5mm - center needle position - upper tension 7-9.
• Draw guidelines on the fabric, spacing them evenly apart.
• Sew from the right side of the fabric.
• Keep rows flat as sewing.
• When finished, steam press the sample, holding the iron over the fabric with the elastic
side up. Do not touch the iron to the fabric.
• Leave the fabric flat until dry.

• Trim all four edges of the sample fabric before beginning.

Fabric:

Rayon Challis - 12” x 4”

Needle:

80/12 Universal

Thread:

All-purpose sewing
Elastic thread (bobbin)

Presser Foot:

Reverse Pattern Foot #1

Other:

Black Latch Bobbin Case

«
...
55
56
57
58
59
...
»

Summary of Contents for activa 125





























































































Reviews:

No comments

Related manuals for activa 125

Brand: LAZER Pages: 13

Brand: Latento Pages: 60

Brand: Easy Quick Pages: 11

Brand: Radio Shack Pages: 2

Brand: Wallenstein Pages: 31

Brand: Unimig Pages: 16

Brand: UniFlow Pages: 42

Brand: M2M Pages: 20

COPENHAGEN WHEEL

Brand: Superpedestrian Pages: 52

Brand: SR Suntour Pages: 10

Brand: BlueHive Pages: 7

Brand: M&H Pages: 64

Brand: MASCOT Pages: 12

Brand: Jiuzhou Pages: 30

Brand: LAZER Pages: 19

Brand: Kong Pages: 72

Brand: Keith Pages: 44

Brand: Waterpik Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands