Bernina activa 125 Owner'S Workbook Download Page 40

Page: 40 / 92

ASTERING

OUR

BERNINA

1/10/02

activa

125/135 PE/145/

BERNINA

activa

125/135 PE/145

ASTERING

OUR

BERNINA

STRAIGHT STITCH BUTTONHOLES

Fabric:

Linen fabric, 6” x 6”

Stabilizer:

1 piece, 3” x 6”

Needle:

90/14 Embroidery

Thread:

30 weight cotton embroidery

Presser Foot:

Auto Buttonhole Foot with Slide #3A

This exercise is for the

activa

145

only

Owner’s manual page___
• Select stitch #12.
• Attach Automatic Buttonhole Foot with Slide #3A to the machine.

Sample #1

Note: Straight stitch buttonholes can be used to pre-sew and reinforce buttonholes on

fabrics which fray easily. The buttonhole beads and bartacks will cover the stitching.

• Mark three lines perpendicular to the fold, spacing them about 2” apart.
• Move the red slide on the foot to 29mm.
• Position the fabric under the neeedle, aligning the fold with the

” marking behind the foot.

• Stitch the buttonhole on the first line -

Do not remove the fabric.

• Select stitch #10 - sew this buttonhole (the same 29mm size) on top of the straight stitch buttonhole.

Sample #2

Note: Straight stitch buttonholes can be used as a buttonhole on imitation suede and leather.

• Select stitch #12 again and sew a straight stitch buttonhole on the second line.

Sample #3

Note: The distance between the prestitched lines can be adjusted with the stitch width.

• Adjust the width of the buttonhole to 5mm.
• Sew a second buttonhole on the third line.

Summary of Contents for activa 125





























































































Search results

Summary of Contents for activa 125

Reviews:

Related manuals for activa 125

Brands by name

Popular brands

Bernina activa 125, Owner'S Workbook

Search results

Summary of Contents for activa 125

Reviews:

Related manuals for activa 125

Brands by name

Popular brands