Bernina activa 125 Owner'S Workbook Download Page 11

Page: 11 / 92

ASTERING

OUR

BERNINA

1/10/02

activa

125/135 PE/145/

BERNINA

activa

125/135 PE/145

ASTERING

OUR

BERNINA

BASTING

Fabric:

Firm fabric – 2 pieces, 4” x 6” each

Needle:

90/14 Embroidery

Thread:

30 wt. cotton embroidery
Contrasting color

Presser Foot:

Reverse Pattern Foot #1

Owner’s manual pg.____
• Place fabric pieces right sides together.

135 PE/145:

• Select the basting stitch (#14 on the 135 PE and #15 on the 145)
• Baste a

” seam along one edge of the fabric using the following steps:

- Position fabric under the presser foot and sew one stitch; hold threads when starting.
- Pull the fabric from behind, creating the desired stitch length.
- Continue in this manner until the seam is complete.

125:

• Select Straight Stitch #1; adjust the length to 5mm
• Baste a

” seam along one edge of the fabric.

Note: Loosening the top tension makes the stitches easier to remove.

Summary of Contents for activa 125





























































































Search results

Summary of Contents for activa 125

Reviews:

Related manuals for activa 125

Brands by name

Popular brands

Bernina activa 125, Owner'S Workbook

Search results

Summary of Contents for activa 125

Reviews:

Related manuals for activa 125

Brands by name

Popular brands