background image

11

Operating the valve with the 

Subtv

 controller reduces the too  

high pressure settings during the low demand hours.  
For example, in typical such pressure regime, the day low 
pressure hours are between 10:00 AM and 06:00 PM and the 
night low pressure hours are between 10:00 PM and 06:00 AM, 
during the high demand hours the valve maintains the high  
pressure setting. 

Therefore, the three required program parameters of the controller 
are: Operation Time - 8 hours, Operation Days - 7 days and two 
Start Times one at 10:00 and the other at 18:00.

1. Operation Time:

Use the 

 button to move to the Operation Time programming 

screen, this is the screen with blinking 

 icon, blinking triangle 

with the digit 1 in it, and the 

 icon. Use the 

 and the 

 

 

buttons to set the required operation time (8:00 hours in our example).

Press the 

 button to move to the next programming screen 

which is the Operation Days screen.

2. Operation Days:

Use the 

 to set a particular day as an operation day, the cursor 

will advance to the next day. In our example set all 7 week days 
for operation. 

Press the 

 button to move to the next programming screen 

which is the Start Times screen.

3. Start Times:

Use the 

 and the 

 buttons to set the first required Start 

Timed (10:00 in our example).

Press  the 

 button to move to the second Start Time and set  

it as required (22:00 in our example). 

The controller is now set for automatically operating the Pressure 
Management Application. 

Summary of Contents for Subtv

























Reviews: