Bergstrom NITE Phoenix Installation Manual Download Page 54 | Manualshive

Page: 54 / 67

background image

4-1

Heater Installation

Optional Webasto Heater controlled
by the Phoenix controller.

WARNING:

If you have a Webasto

fuel operated heater that was installed at
the factory or prior to the Phoenix
install, you can continue to operate the
heater with the existing controller. IF
you choose to wire the existing factory
installed Webasto heater to the Phoenix
controller,

YOU COULD VOID THE

FACTORY WARRANTY OF THE
HEATER!

DO NOT USE PHOENIX DUCT FOR
HEAT VENT.

ATTN: Refer to Webasto manual for
all  heater  installation  instructions
then  proceed  to  steps  below  for
connecting  Webasto  heater  to  the
Phoenix unit.

Attach Webasto heater control harness
to Phoenix Unit. Route the control
cable along the bed towards the Phoenix
unit. Use zip ties as needed.

Now connect the heater control harness
to the Phoenix unit harness (as shown in
photo). The Webasto heater in the
Phoenix kit is prewired to connect
directly into the Phoenix unit harness.

For pin numbers and wire colors see
wiring diagram in section 5.

«
...
52
53
54
55
56
...
»

Summary of Contents for NITE Phoenix




































































Reviews:

No comments

Related manuals for NITE Phoenix

Brand: Mamiya Pages: 4

Brand: Paradyne Pages: 86

mydlink DSP-W110

Brand: D-Link Pages: 13

Brand: D-Link Pages: 44

Brand: UnderCover Pages: 16

Brand: Safco Pages: 6

Brand: Hama Pages: 2

Brand: Uclear Pages: 2

Brand: Oki Pages: 20

Brand: Talkswitch Pages: 334

Brand: Tait Pages: 41

Brand: Tait Pages: 149

Brand: Tait Pages: 132

Brand: Rice Lake Pages: 2

Brand: FABBRI PORTATUTTO Pages: 2

Brand: probrake Pages: 2

Brand: Magnus Pages: 6

Brand: Fisher-Price Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands