background image

3

 

 

 

OPERATION: 
 

1.  Do not put hands or feet near, under or inside rotating 

parts.  

 

2.  Exercise  extreme  caution  when  operating  on  or 

crossing  gravel  drives,  walks  or  roads.  Stay  alert  for 
hidden hazards or traffic. Do not carry passengers. 

 

3.  After striking a foreign object, stop the engine (motor), 

disconnect  the  wire  from  the  spark  plug(s)  and  keep 
wire  away  to  prevent  accidental  starting.  Thoroughly 
inspect  the  accessory  for  any  damage  and  repair 
damage before restarting and using the accessory. 

 

4.  If the unit should start to vibrate abnormally, stop the 

engine  (motor)  and  check  immediately  for  the 
cause.  Vibration  is  generally  a  warning  of  trouble. 
Don not use equipment until properly repaired. 

 

5.  Take  all  possible  precautions  when  leaving  the 

vehicle  unattended.  Disengage  the  power  take-off, 
lower  the  attachment,  place  the  transmission  into 
neutral,  set  the  parking  brake,  stop  the  engine  and 
remove the ignition key. 

 

6.  Do not run the engine indoors, except when starting 

the  engine  and  for  transporting  in  or  out  of  the 
building. Do not operate or let motor run in a storage 
area  without  ventilation  because  gas  contains 
carbon  monoxide  which  is  odorless,  colorless  and 
can cause death. 

 

7.  Never  use  the  accessories  across  the  face  of 

slopes,  go  from  top  to  bottom.  Exercise  extreme 
caution  when  using  equipment  on  slopes,  on  wet 
ground  or  near  drop-off.  Do  not  attempt  to  use 
accessory on a steep slope. 

 

8.  Never  tolerate  bystanders  in  the  working  zone. 

Never  use  an  accessory  in  the  direction  of 
bystanders,  it  might  throw  gravel  or  debris  that  can 
hurt people or damage property. 

 

9.  Never  operate  the  accessory  at  high  transport 

speeds  on  slippery  surfaces.  Use  care  when 
backing up. 

 

10.  Do not carry passengers. 

 

11.  Disengage  power  to  the  accessory  when  it  is 

transported or not in use. 

 

12.  Never  operate  the  accessory  without  good  visibility 

or light. 

 

13.  Keep  the  accessory  away  from  heat  sources  or 

flames. 

 

14.  If  applicable,  never  handle  the  winch  cable  or  hook 

while under tension. 

15.  Never  use  accessory  if  it  has  been  dropped  or 

damaged. Repair if necessary before re-using. 

 

MAINTENANCE AND STORAGE 
 

1.  When  cleaning,  repairing  or  inspecting  the  vehicle 

and  accessory:  park  on  a  solid  level  ground, 
disengage  drives,  lower  implement,  set  parking 
brake,  stop  the  engine,  remove  ignition  key,  and 
wait  that  all  moving  parts  have  stopped.  For 
gasoline  engine,  disconnect  wire  from  the  spark 
plug(s)  and  keep  wire  away  to  prevent  accidental 
starting. 

 
2.  Check  all  the  bolts  and  components  at  frequent 

intervals  to  make  sure  that  they  are  properly 
tightened and in safe working condition. 

 
3.  Never  store  a  motorized  accessory  with  fuel  in  the 

fuel tank inside a building where ignition sources are 
present  such  as  hot  water  and  space  heaters, 
clothes dryers, and the like. Allow the engine to cool 
before storing in any enclosure. 

 
4.  Alway

s refer to the owner’s manual when you store 

the  accessory  and  vehicle  for  a  prolonged  or  an 
unspecified length of time. 

 
5.  Maintain or replace safety and instruction labels, as 

necessary. 

 

For winter accessories, (if applicable), let the engine 
run for a few minutes after clearing snow in order to 
prevent the rotary parts from freezing. 

 
7.  

Inspect  the  vehicle’s  and  accessory’s  air  filter 

(if 

applicable)  every  day.  Clean  it  or  replace  it  as 
necessary. Change the oil more often when working 
in  dusty  con

ditions.  See  the  vehicle’s  and 

accessory's owner’s manual.

 

 
8.   When inflating tires, stand on one side NOT in front 

or  over  the  tire  assembly.  Use  a  safety  cage  if 
available 

 

TRANSPORT  
 

1.  Review  Transport  Safety  instructions  in  vehicle 

manual before moving or hauling. 

 
2.  Check  with  local  authorities  regarding  transport  on 

public  roads  and  off  road.  Obey  all  applicable  laws 
and regulations. 

 
3.  Make sure  all lights and reflectors that are  required 

by  the  local  highway  and  transport  authorities 
(exemple  :  SMV  (Slow  Moving  Vehicle))  are  in 
place,  are  clean,  and  can  be  seen  clearly  by  all 
overtaking and oncoming traffic. 

 
4.  Never  have  the  equipment  in  operation  during 

transport. 

 
5.  Always travel at a safe speed. 

 

SAFETY PRECAUTIONS 

 
 

Summary of Contents for 700580-4





































































































Reviews: