background image

                                                                                   

Last revised:    May 17, 2013                                                                                                                               

16 

    

3.

3.

3.

3.

 

Use correctly rated materials

Use correctly rated materials

Use correctly rated materials

Use correctly rated materials    

Use special solar cable and suitable connectors only. Ensure that they are in perfect 

electrical and mechanical condition. Use only single wire cables. Select a suitable 

conductor diameter to minimize voltage drop. 

 

4.

4.

4.

4.

 

C

C

C

Cable protection

able protection

able protection

able protection    

Secure the cables to the mounting system using UV-resistant cable ties. Protect exposed 

cables from damage using suitable precautions. Avoid direct exposure to sunlight. 

 

4.3 Limitation of Connection (ETL) 

 

The UL 1703 certificate of these modules guarantees their insulation up to a DC voltage of 

1000 V (UL 1703 Standard).   

 

However, a cable with a suitable cross section must be used for conducting the sum of the 

currents as generated by the modules. A series protection fuse of 15A is recommended for 

each string when module strings are wired in parallel. 

 

BenQ Solar recommends the PV conductor, which cross section is 4 mm2.    External 

connection boxes can be used to enable greater cable cross section area for long distance 

transmission. 

 

The modules are qualified for the application class A: Hazardous voltage (IEC 61730: higher 

than 50V; EN 61730: higher than 120V), hazardous power applications (higher than 240W) 

where general contact access is anticipated. 

 

 

Summary of Contents for PM245P01 Series























Reviews: