background image

 

 

Relay on the circuit board is stuck 

Contact supplier. 

Acid pump only doses occasionally 

Sour pump is set to proportional 
dosing 

No action required 

Chlorine pump does not dose 
 

Switch under the dosing pump is 
set to "O". 

Set switch to "1 

Settings of Rx control are incorrect 

Verify settings 

A level detector is connected that 
gives a wrong contact 

Disconnect level detector 

A flow sensor is connected and 
indicates that there is no flow. 

Verify flow and flow switch (go to 
setting flow switch : no) 

Chlorine pump continues dosing 
 

Setpoint not yet reached 

Verify settings and verify chlorine 
content with color method. 

Relay on the circuit board is stuck 

Contact supplier. 

Acid pump and chlorine pump do 
not pump. 

A flow switch is connected and it 
shows that there is no flow 

Verify flow and flow switch (go to 
setting flow switch : no) 

 

There are level detectors 
connected that give a wrong 
contact 

Disconnect level detectors 

Chlorine or acid pump do not draw 
in liquid 
 

Vessel is empty or suction base is 
above liquid level 

Replace acid or chlorine container; 
Lower suction base. 

Suction base is blocked 

Replace suction base ZWMX2205-Z 

Peristaltic hose is leaking 

Replace peristaltic hose 
ZWMX2231-Z 

Injection nozzle is blocked 

Replace injection nozzle 
ZWMX2220-Z 

Liquid (acid or chlorine) in dosing 
compartment of chlorine or acid 
pump 

Santoprene dosing hose leaking 

Verify if dosing nipple is clogged, 
and replace dosing hose. 

Dose hose in pH or chlorine dosing 
chamber forms a bladder 

Acid or chlorine supply in injection 
nipple blocked by dirt / 
calcification 

Stop acid dosing immediately and 
clean/replace nipple. Use liquid 
chlorine with anti-scaling 

Calibration failed 
 

Calibration fluid outdated or dirty 

Replace calibration fluid 

Probe not yet balanced 

Repeat calibration 

Probe broken 

Replace probe 

Probe dry for a long time 

Leave probe in pool water for 24 
hours, and recalibrate 

Summary of Contents for ZPTX0010-P





























Reviews: