XPR-10 Series Two-Post Lifts
36
P/N 5900951 — Rev. D — May 2019
Installing the Overhead Assembly, Safety Shutoff Bar, and the
Microswitch
The Overhead Assembly goes above and between the Powerside and Offside Posts. It holds the
Equalizing Cables, the Hydraulic Lines, the Microswitch wiring, and the Safety Lock Cable.
The Safety Shutoff Bar and the Microswitch (or two Microswitches if you ordered a three-phase Power
Unit) are installed on the underside of the Overhead Assembly.
The Safety Shutoff Bar shuts off power to the Lift if the top of a Vehicle hits it; this trips the
Microswitch, which cuts off power to the Lift, preventing it from going any higher.
The Microswitch
wiring
goes over the Overhead Assembly and down the Powerside Post to the
Power Unit. Wiring the Microswitch is not covered in this section; it is covered in
Wiring the
Microswitch
. Have your Electrician connect the Microswitch wiring to the Power Unit when they
come out to perform the other electrical tasks.
The Overhead Assembly is two pieces that are bolted together. The Overhead Assembly and the
Safety Shutoff Bar come from the factory already assembled in the Narrow Configuration. On rare
occasions, the two pieces could come from the factory unassembled.
This leaves you with these options:
•
You want the Wide Configuration
. If the Overhead Assembly and the Safety Shutoff Bar
came from the factory assembled in the Narrow Configuration, and you earlier decided on the
Wide Configuration, you need to change the Overhead Assembly and the Safety Shutoff Bar to the
Narrow Configuration, install the Microswitch, and then put the Overhead Assembly into place.
Note
: The Narrow or Wide Configuration decision should already have been made (in
Choosing a
Wide or Narrow Configuration
). Refer to that section for additional information.
•
You want the Narrow Configuration
. If the Overhead Assembly and the Safety Shutoff Bar
came from the factory assembled in the Narrow Configuration, which is what you want, install the
Microswitch and then put the Overhead Assembly into place.
•
The Overhead Assembly comes unassembled
. If the Overhead Assembly and the Safety
Shutoff Bar came from the factory unassembled, install the Overhead Assembly in the desired
configuration (using the drawings in this section as guides), install the Safety Shutoff Bar, install the
Microswitch, and then put the Overhead Assembly into place.
BendPak recommends putting the Overhead Assembly on saw horses to prepare it.
To prepare and install the Overhead Assembly
:
1.
If the Overhead Assembly came unassembled, locate the two Overhead Assembly pieces and the
four M10 x 1.5 x 25 Hex Head Bolts, four M10 x Ø20 Flat Washers, four M10 x Ø18 Split Lock
Washers, and four M10 x 1.5 Nuts needed to connect them.
If your Overhead Assembly came assembled from the factory, even if in the wrong configuration for
your installation, these pieces are already in place.
2.
Put the Overhead Assembly together in the desired configuration.
3.
Remove all four Overhead Assembly Sheaves and their Pins and Bolts from the ends of the
Overhead Assembly pieces.
Keep them nearby, you will be putting them back into place in the next section of the installation.
Summary of Contents for XPR-10 Series
