LR-10000 Low-Rise Scissor Lift
28
P/N 5900075 — Rev. A1 — April 2019
If you are unsure where the Lifting Points are, consult
Vehicle Lifting Points for Frame Engaging
Lifts
, which was provided with the Lift, or the manufacturer of the Vehicle. If you no longer have
Vehicle Lifting Points for Frame Engaging Lifts
, you can get a replacement on the ALI website.
⚠
WARNING
Do not ‘eyeball’ the best location for the Lift Pads.
The Lift Pads must hit the
manufacturer’s recommended Lifting Points
. If you do not, the Vehicle
could become unstable and fall, which could damage the Vehicle, damage the Lift,
or injure or even kill anyone under the Vehicle.
7.
Put the Lift Pads under the Vehicle so that they are
directly under
the Lifting Points for the
Vehicle you are raising.
If necessary, use the included Lift Pad Extensions for extra height. You can also stack them.
8.
On the Power Unit, press and hold the
Raise
button to raise the Lift until
just before
the Lift
Pads make contact with the Lifting Points on the underside of the Vehicle.
9.
Check to make sure the Lift Pads will make solid contact with the Lifting Points when raised
further.
Adjust them if necessary.
10.
Raise the Lift until the tires of the Vehicle are a few inches off the ground.
11.
Visually check to make sure the Lift Pads are making solid contact with the Lifting Points.
If any of the Lift Pads are
not
making solid contact with the Lifting Points, lower the Lift and adjust
the Lift Pads so that they make better contact.
12.
Rock the Vehicle to make sure the Vehicle is stable and balanced.
If the Vehicle is
not
stable and balanced, lower the Lift back to the ground and start over.
If the Vehicle
is
stable and balanced, it is safe to raise further.
⚠
DANGER
Do not raise the Lift further until you are certain the Vehicle on the Lift is both stable
and balanced. If the Vehicle is
not
stable and balanced, it could fall, which could
damage the Vehicle, damage the Lift, or injure or kill anyone under the Vehicle.
13.
On the Power Unit, press and hold the
Raise
button.
14.
Watch the Vehicle and the Platforms as they rise.
If the Lift becomes unstable or the Vehicle starts moving, release the
Raise
button immediately.
15.
When the Platforms are
just past
the desired height, release the
Raise
button.
The Lift stops rising.
16.
Press the Lowering Handle on the Power Unit to move the Platforms back down a little, which
engages them on the most recently passed Safety Lock.
If you miss the Safety Lock, press and hold
Raise
again and go somewhat further past the Safety
Lock, then hold the Lowering Handle again to engage the Lift on the Safety Lock.
17.
To lower the Lift back down to the ground, pull up on the Safety Lock Release Handle, then press
and hold the Lowering Handle until the Lift is fully lowered.
If the Lift was shaking, moving erratically, or squeaking, raise and lower the Lift again to help bleed
the Hydraulic System.
If you continue to have issues, refer to
Summary of Contents for LR-10000
