BendPak HD-14T Installation And Operation Manual Download Page 1

Page: 1 / 76

1645 Lemonwood Dr.

Santa Paula, CA 93060 USA

Toll Free: (800) 253-2363

Tel: (805) 933-9970

bendpak.com

HD-14T Four-Post Lift

Installation and Operation Manual

Manual P/N 5900037 — Manual Revision F — February 2022

Designed and engineered by BendPak Inc. in Southern California, USA. Made in China.

⚠

DANGER

MPORTANT

AFETY

NSTRUCTIONS

AVE

HESE

NSTRUCTIONS

Save these instructions! Read the

entire

contents

of this manual

before

using this product. Failure to

follow the instructions and safety precautions in this manual can
result in serious injury or death. Make sure all other operators also
read this manual. Keep the manual near the product for future
reference.

By proceeding with installation and operation, you

agree that you fully understand the contents of this manual
and assume full responsibility for product use

Models:

•

HD-14T

Summary of Contents for HD-14T












































































Search results

Summary of Contents for HD-14T

Reviews:

Related manuals for HD-14T

Brands by name

Popular brands

BendPak HD-14T, Installation And Operation Manual

Search results

Summary of Contents for HD-14T

Reviews:

Related manuals for HD-14T

Brands by name

Popular brands