6. Doctor ID setup
Preset positions can be set up for four doctors using doctor IDs, which is useful for an associate clinic.
[Setup procedure]
1. Press the mode SW until the beeper sounds (about 2 seconds). The beeper will sound three times.
2. Press the SW shown below according to the doctor ID to complete the setup.
Doctor ID Doctor 0 Doctor 1 Doctor 2 Doctor 3
SW to be pressed 0 P1 P2 LP
[Note] To abort the registration, press the Store SW. Pressing the mode SW will shift the mode to the beeper sound setup mode.
The registration mode is terminated automatically after a lapse of 10 seconds. When the chair is connected to a unit equipped
with a communication system, changing the doctor IDs on the chair will not affect the IDs on the unit side.
7. Beeper sound setup
Enables or disables the beeper sound at SW inputs.
[Setup procedure]
1. Press and hold down the mode SW until the beeper sounds (about 2 seconds).
The beeper will sound three times. (The mode shifts to the doctor ID setup mode.)
2. Press the mode SW once again. The beep will sound four times.
3. Press the following operation SWs to select a function. Enabled and Disabled statuses toggle every time the SWs (other than A.R.)
are pressed.
Operation SW Beeper functions to be changed
A.R.
All the beeper sounds below, except for setup and alarm, are disabled.
Chair-up
The beeper sound at the operation SW pressing is enabled/disabled.
Chair-down The beeper sound at the 4-bit input is enabled/disabled.
Backrest-raise The beeper sound at the operation signal from the serial (communication line) input is enabled/disabled.
Backrest-recline The beeper sound at the Prohibit lower input is enabled/disabled.
P1 The beeper sound at the Prohibit all input is enabled/disabled.
The beeper enable/disable setups can be performed successively.
4. After the setups are done, press the Store SW.
[Note] The only way to cancel the setup mode is to leave it for 10 seconds or more without any operations. Pressing the mode SW again
will shift the mode to the leg rest operation mode. The mode is terminated automatically after a lapse of 10 seconds.
5. Auto return, preset, and rinsing position setup
There are two different setup procedures but the results are the same.
[Setup procedure 1]
1. Move the chair to the desired position.
(Also, move the leg rest to the desired extension or retraction limit position.
For the procedure to move the leg rest, refer to 8. Independent operation of the leg rest.)
2. Press the desired SW (0, P1, P2, LP etc.) for that position until the beeper sounds (about 5 seconds) to complete the procedure.
0: Auto return P1, P2: Preset, LP: Rinsing position as the last position
[Setup procedure 2]
1. Move the chair to the desired position.
(Also, move the leg rest to the desired extension or retraction limit position.
For the procedure to move the leg rest, refer to 8. Independent operation of the leg rest.)
2. Press and hold down the Store SW (about 2 seconds).
After the initial beeper sound, the beeper keeps on sounding once at the ‘ pip, pip’ (ten times at one second intervals).
3. Press the desired SW (P1, LP etc.) for that position to complete the procedure.
If the step 3 does not take place within 10 seconds, the procedure is terminated. (Setup of the Auto return position is not available.)
4. To exit the procedure during the step 2, press the Store SW once again.
[Note] Setting up the same position for the second time for the switch to which the position is already programed is not available.
For example, an attempt to setup the P1 position while the chair is in the P 1 position is ignored. To set up an Auto return
position, follow the procedure described in [Setup procedure 1].
If the rinsing position is set up at the same position as the upper limit, lower limit, or forward limit position, the actual rinsing
position will be set a little short to each limit position to ensure operational stability. For example, if the registered rinsing
Position is identical to the lower limit position, the actual rinsing position will be set a little higher than the lower limit.
-3-
