manualshive.com logo in svg

Belfort AWOS, Maintenance Manual

Share
Download
Belfort AWOS Maintenance Manual Download Page 94

  

BELFORT

 

INSTRUMENT 

Proprietary Information

 

 

 

Belfort AWOS Atomic Clock Verification Procedure 

 

 

 

 

 

 

 

 

 

 

 

06/01/2014 

 
 

The Belfort AWOS Atomic Clock can be tested, configured and verified using the following 
procedure. 
 
Units are typically not shipped with batteries installed. The unit uses 3 AAA batteries.  Do 
not use rechargeable batteries is this unit. 
  
The unit can be connected to the PC using a USB cable.  When connected with the PC, a 
7vdc wall pack is also required and supplied.   

 
 

1. 

The cable to the PC and the optional wall pack power supply disconnected, remove 
the top 4 cover screws.  Open the cover. 
 

2. 

If the batteries are not installed, install 3 AAA batteries.  Verify the correct battery 
polarity during their installation.   

 

3. 

Re-install the cover with 4 cover screws. 

 

4. 

Connect the USB cable from the PC to the Unit Under Test (UUT). 

 

5. 

Connect the unit to the PC with its USB cable and wall pack power supply. 

 

6. 

On the PC, start Hyper-terminal (HT) at 9600, 8, N, 1, no handshaking.  In HT select 
the PC USB Com port that the Atomic Clock is connected to. 

 

7. 

In HT, enter the command RN followed by the enter key. 

 

8. 

The unit should respond with the unit serial number in the following message format.  
Verify that the serial number is correct.  If not correct, contact the Belfort Service 
Tech or Belfort Factory for directions.  If the serial number is received, this means 
that communications with the unit is good and the unit is working. 

 

1.  N 102 

 

9. 

In HT, enter the command RB followed by the enter key.  The unit should respond 
with the battery voltage in the following message format: 

 

1.  B 4.84 

 

10. 

The battery voltage can range from 3.5 Vdc to 4.8 Vdc.  If the battery voltage is at or 
below 3.5v, disconnect the unit from the PC and replace the 3 AAA batteries with 
others of the same type.  Reconnect the unit to the PC with power and repeat the RB 
command. 

Summary of Contents for AWOS
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands