manualshive.com logo in svg

Belfort AWOS, Maintenance Manual

Share
Download
Belfort AWOS Maintenance Manual Download Page 89

  

BELFORT

 

INSTRUMENT 

Proprietary Information

 

 

DCP Site Configuration Procedure: 

 
 

The DCP must be configured with the specific information for the destination airport.  
Access the WEB site WWW.airnav.com and enter the specific airport designator for the 
destination airport.  Print the complete package of information for the airport.  When the 
configuration is completed, staple the complete Air Nav Document to the Comprehensive 
Facility Performance and Adjustment Form.  

 

1.

 

In the DCP Power Enclosure, turn off AC power by turning off circuit breaker 1. 

 
2.

 

In the DCP Power Enclosure, turn off DC power by turning off circuit breaker 2. 

 

3.

 

Lower the tower to gain access to the bad DCP. 

 
4.

 

Remove the four mounting screws holding the Bad DCP to the tower.  

 
5.

 

Disconnect all cable connectors from the unit.  Note the locations of the cable connectors 
when connected to the DCP. 

 

6.

 

Connect the cables to the new DCP.   

 

7.

 

Re-install the four mounting screws to hold the new DCP to the tower.  

 

8.

 

Connect the PC to the DCP cable dongle in the DCP Power Enclosure. 

 

9.

 

On the PC, open a DOS window and browse to the TXCOM program for the version of 
DCP program in the UUT.  Start the TXCOM program as follows: 

 

 

Enter “acbstxcom108A comx”<cr>. 

 
 

Acbstxcom108A is the revision for DCP’s with firmware code version 1.05D, and comx 

(com1-com8) is the serial port as configured on the PC to be used for testing. 

 

10.

 

The TXCOM program will respond with a hyphen (“-“) prompt. 

 
11.

 

In the DCP Power Enclosure, turn ON AC power by turning on circuit breaker 1. 

 

12.

 

Immediately enter on the PC, the monitor command by entering “m” <cr>. 

 

13.

 

If the unit responds with an “Enter Password” message, enter the default password 
“XXXXXXXXX”, <cr>. 

 

Summary of Contents for AWOS
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands