manualshive.com logo in svg

Belfort AWOS, Maintenance Manual

Share
Download
Belfort AWOS Maintenance Manual Download Page 11

-8- 

BELFORT

 

INSTRUMENT 

Proprietary Information

 

 

Figure 1a 

Advisor Main Screen 

 
 
 
Advisor software also captures this status and compares it to the last status received and if there 
is a difference in any of the data, writes all the data to the Advisor Status Log and to the Advisor 
Current Status Page.  See Figure 1b below. 

 

 

 

Figure 1b  

System Status Page 

 

The  System  Status  Page  is  updated  when  the  page  is  accessed.    To  reread  the  status,  the 
technician  must  select  the  Return  Button  then  access  the  System  Status  page  again  for 
updated status. 

 
At any time the maintenance technician can view the most recently received Status Information 
displayed in a user-friendly format. The maintenance technician can also view the Status Change 
History  for  past  or  recurrent  problems.    View  the  Status  Pages  past  history  by  selecting  Status 
Pages  from  the  History  menu  entry  on  the  Advisor  main  menu.  Refer  to  the  Belfort  AWOS 
"Operator Instruction Manual” for complete user instructions for operating the Advisor software.  
5.  Document any error flags on the Tri-annual or Annual “Facility Performance and Adjustment” 

data form. 

Summary of Contents for AWOS
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands