Beijer Electronics EXTER T100 Service And Maintenance Manual Download Page 28 | Manualshive

Page: 28 / 54

background image

Hardware

28

Beijer Electronics, MA00757A

EXTER T40/T40m

To replace the display you will need a new display including display frame, see
the

Available Spare Parts

section.

Follow the steps below:

1. Power off the operator terminal.

2. Follow the instructions under

Replacing the Rear Cover

to remove the rear cover.

3. Unlock the flex cable connector by pressing the connector flanges towards the

cable and disconnect the flex cable and the plain cable from the power card.
The connector must be unlocked on both sides before removing the cables.

4. Gently press the power card towards the top of the terminal as shown in the

illustration above to release the power card from the power card holders.
Then tilt the bottom of the card away from you.

5. Disconnect the flex cable on the back side of the power card and remove the

power card.

6. Insert the two screwdrivers between the display frame and the aluminum casing

illustrated below. Press and bend gently on the display frame to unlock the frame
and tilt up the display frame.

7. Mount the new display unit.

8. Re-assemble the complete operator terminal.

power card

flex cable

plain cable

display frame pressure points

«
...
26
27
28
29
30
...
»

Summary of Contents for EXTER T100























































Reviews:

No comments

Related manuals for EXTER T100

Brand: Nelsen Corporation Pages: 16

Brand: National Instruments Pages: 34

Brand: Bang & Olufsen Pages: 9

Brand: Bang & Olufsen Pages: 12

Brand: Hach Pages: 86

Brand: ZETRON Pages: 3

Brand: ADEMCO Pages: 2

Brand: Unipulse Pages: 99

Brand: Accutrol Pages: 25

Brand: Mainpine Pages: 16

Brand: Danfoss Pages: 20

Max Charge MC-624

Brand: Balmar Pages: 8

MAX CHARGE MC-614

Brand: Balmar Pages: 20

Brand: Febco Pages: 12

Brand: GameSir Pages: 8

Brand: Game ready Pages: 21

Brand: VAMP Pages: 304

Brand: Tactical Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands