MINIMON MON800
Controls
(EN)
Controls
For more details on the full functionality of this product,
see the product page on behringer.com and download the
full manual.
(1)
(2)
(3)
(8)
(11)
(12)
(13)
(6)
(4)
(7)
(9)
(10)
(5)
(14)
(17)
(16)
(15)
(18)
(19)
(20)
(21)
(22)
(1)
Use the four switches in the
SOURCE
section to select up to four
input sources (MIX A and B, CD/TAPE C and D) for monitoring
and recording.
(2)
The two LED displays are for monitoring the output level of the
2-TRACK OUT outputs. They comprise 6 LEDs each. When the
CLIP
LED lights up, this indicates that distortion may occur.
(3)
A pair of headphones with a ¼" TRS connector
(e.g. BEHRINGER HPS5000) can be connected to the
PHONES
jack. This output is wired in parallel with the
rear-panel output jack
(15)
, so that up to two headphones
can be used at the same time.
(4)
With the
PHONES LEVEL
control you can adjust the
volume for the two headphones jacks on the front or rear
panel respectively.
(5)
SPK A LEVEL
governs the volume level of the SPEAKERS OUT
A outputs
(18)
. SPK B+C LEVEL allows you to set the volume for
outputs B and C
(17)
simultaneously.
(6)
Use the switches
A/B/C ON
to switch the speakers A,
B and C on and off.
(7)
With the
MUTE
switch you can disable all loudspeaker and
headphones outputs.
(8)
The
MONO
switch switches all monitor paths to mono.
(9)
The
DIM
switch lowers the level of the monitor paths by -20 dB.
This allows you, for example, to talk to somebody while mixing
without losing track of the recording.
(10)
Use the
TALK LEVEL
control to adjust the sensitivity of the
talk-back microphone.
(11)
The talk-back microphone is installed behind the
MIC
openings.
Speak into the microphone to make announcements which
are then routed to the recording devices connected to the
2-TRACK OUT outputs.
(12)
The
TALK TO CUE/PHONES/SPK A
and
TALK TO 2-TR OUT
buttons determine where the talk-back microphone signal is
routed to
(
9
)
.
(13)
The switch turns your MINIMON MON800 on and off.
(14)
The MON800 is connected to the mains using a 2-pole
POWER
connector jack. A matching mains adaptor is
included with the unit.
(15)
A second pair of headphones can be connected to the
PH
jack.
This connector is wired in parallel with the front-panel jack
(3)
.
(16)
The
TB
jack is used to connect a single footswitch
(12)
.
(17)
Two pairs of loudspeakers can be connected to the
SPEAKERS
OUT
B
and
C
jacks.
(18)
Connect your main monitor speakers to the
SPEAKERS OUT
A
jack.
(19)
CUE OUT
is an additional output, which you can use to route
the MINIMON signals to other devices, such as an additional
headphones amp.
(20)
The two
2-TRACK OUT
jacks are wired in parallel and carry the
same signals. Use the ¼" or cinch outputs, depending on the
recording device used.
(21)
Use the
CD/TAPE IN
jacks C and D to connect playback devices,
such as a computer, CD/MD or cassette player.
(22)
The
MIX IN
jacks A and B are for connecting the main signal
sources (e.g. mixing console, audio card, etc.) using ¼" plugs.
Mono signals must be connected to the L jacks.
16
MINIMON MON800
17
Quick Start Guide
