Beha-Amprobe GT-600 User Manual Download Page 39

Page: 39 / 76

GT-600/GT-800 Instruction Manual

Specific information that can be shown on the display

Information displayed

Description

EXTERNAL VOLTAGE

External voltage is applied to one or more
test terminals, see the explanation in section
“Pre-Tests and Protection”.

Warning! Mains voltage will be applied to
test socket after confirming this message!

SUB

> 3.50 mA

Substitute leakage current is higher than
3.50 mA. Dangerous, check the appliance!

TIME OUT

There was no action (no key pressed) for
more than 1 minute (repeat the test from
the beginning) or the PRCD is faulty.

PRESS PRCD ON

Press ON button on PRCD!

PRESS PRCD TEST

Press TEST button on PRCD!

PRESS STOP

Press STOP button on GT-800!



In order to save displayed measurement results see the “Memorizing
example” section.

MAINS SWITCH ON

CONTINUE?

Summary of Contents for GT-600













































































Search results

Summary of Contents for GT-600

Reviews:

Related manuals for GT-600

Brands by name

Popular brands

Beha-Amprobe GT-600, User Manual

Search results

Summary of Contents for GT-600

Reviews:

Related manuals for GT-600

Brands by name

Popular brands