Beckman Coulter Biomek NXP Preinstallation Manual Download Page 49

B20063AC    

Warranty-1

Beckman Coulter, Inc.

Warranty and Returned Goods Requirement

All standard Beckman Coulter, Inc. policies governing returned goods apply to this product. Subject to the 

exceptions and upon the conditions stated below, the Company warrants that the products sold under this 

sales agreement shall be free from defects in workmanship and materials for one year after delivery of the 

products to the original Purchaser by the Company, and if any such product should prove to be defective 

within such one year period, the Company agrees, at its option, either (1) to correct by repair or at the 

Company’s election by replacement, any such defective product provided that investigation and factory 

inspection discloses that such defect developed under normal and proper use, or (2) to refund the purchase 

price. The exceptions and conditions mentioned above are as follows:

1.

Components or accessories manufactured by the Company which by their nature are not intended to and 

will not function for one year are warranted only to reasonable service for a reasonable time. What 

constitutes a reasonable time and a reasonable service shall be determined solely by the Company. A 

complete list of such components and accessories is maintained at the factory.

2.

The Company makes no warranty with respect to components or accessories not manufactured by it. In 

the event of defect in any such component or accessory, the Company will give reasonable assistance to 

Purchaser in obtaining from the manufacturer’s own warranty.

3.

Any product claimed to be defective must, if required by the Company, be returned to the factory, 

transportation charges prepaid, and will be returned to Purchaser with transportation charges collect 

unless the product is found to be defective, in which case the product must be properly decontaminated 

of any chemical, biological, or radioactive hazardous material.

4.

The Company shall be released from all obligations under all warranties, either expressed or implied, if 

any product covered hereby is repaired or modified by persons other than its own authorized service 

personnel, unless such repair by others is made with the written consent of the Company.

5.

If the product is a reagent or the like, it is warranted only to conform to the quantity and content and for 

the period (but not in excess of one year) stated on the label at the time of delivery.

It is expressly agreed that the above warranty shall be in lieu of all warranties of fitness and of the warranty 

of merchantability, and that the company shall have no liability for special or consequential damages of any 

kind or from any cause whatsoever arising out of the manufacture, use, sale, handling, repair, maintenance, 

or replacement of any of the products sold under the sales agreement.

Representatives and warranties made by any person, including dealers and representatives of the Company, 

which are consistent or in conflict with the terms of this warranty, shall not be binding upon the Company 

unless reduced in writing and approved by an expressly authorized officer of the Company.

 Parts replaced during the warranty period are warranted to the end of the instrument warranty.

NOTE:

Performance characteristics and specifications are only warranted when Beckman Coulter replacement parts 

are used.

Except as provided in writing signed by an officer to Beckman Coulter, Inc., this system and any 

related documentation are provided “as is” without warranty of any kind, expressed or implied, 

including that the system is “error free.” This information is presented in good faith, but Beckman 

Coulter does not warrant, guarantee, or make any representations regarding the use or the results 

of the use of this system and related documentation in terms of correctness, accuracy, reliability, 

currentness, omissions, or otherwise. The entire risk as to the use, results, and performance of this 

system and related documentation is assumed by the user.

Summary of Contents for Biomek NXP





















































Reviews: