Beam RST825 SatRADIO User And Installation Manual Download Page 26

Page: 26 / 30

Page 26 of 30

Radio (SRM9000 Transceiver)

Frequency range

(sub-bands)

136MHz to 174MHz, 403-480MHz, 440-520MHz

Channel Spacing

10 / 12.5 / 20 / 25kHz

Current consumption

(typical)

220mA S/By, 1100mA Tx, 800mA Rx

(Speaker enabled)

RF Power Output

5 Watts

Receiver Sensitivity

≤ 0.3µV PD (

-117.5dBm) for 12dB SINAD

Adjacent Channel Selectivity

25kHz Channel Spacing > 73dB

(AS4295)

>70dB (ETS)

12.5kHz Channel Spacing > 65dB

(AS4295)

>60dB (ETS)

Frequency stability

±2.5 ppm

Spurious Response Rejection

> 75dB (AS4295), >70dB (ETS)

Input/output impedance

50 Ohms – N Series F Connector

Conducted Spurious Emissions

< 2nW (-57dBm) 9kHz to 1GHz (ETS)
< 20nW (-47dBm) 1GHz to 4GHz

FM Hum & Noise

>45dB VHF, >40dB UHF

Modulation

FM Analog, P25 Digital (specific models only)

Encryption ( P25 Digital Models only)

Optional DES-OFB, AES

Environmental

Operational Temperature

-30°C to +60°C

Storage Temperature

-40°C to +80°C

Vibration

MIL-STD-810F 514.5

Temperature

MIL-STD-810F 501.4

Humidity

MIL-STD-810F 507.4

Product Sealing

IEC529 rating IP54

Certification

SRM9000 Type Acceptance

FCC,

ETS300 086 Radio; ETS300 113 Data;

ETS300 279 EMC; ETS300 219 Sig; AS/NZS4295

Safety

A Tick

RST825 EMC/EMI Compliance

EN61000-6-2, EN61000-6-4, EN61000-3-2, EN61000-3-
3, FCC Part 15B Class A, C Tick CISPR22 Class A

Additional Certification for Iridium Transceiver:

The following harmonised standards have been applied to the design of the L-band
transceiver:

Standard

EN 60950-1:2001

EN 301 489-20V1.2.1 (200211)

Description

Information technology equipment – Safety – Part 1: General Requirements

Electromagnetic compatibility and Radio Spectrum Matters (ERM);

EN 301 489-01v1.4.1 (2002-08)

Electromagnetic compatibility (EMC) standard for radio equipment and services.

ETSI EN 50360:2001

Product standard to demonstrate the compliance of mobile phones with the basic
restrictions related to human exposure to electromagnetic fields (300MHz to
3GHz)

ETSI EN 301 441 V1.1.1 05/2000 Satellite Easrth Stations and Systems (SES); Harmonised EN for Mobile Earth

Stations MESs)

Summary of Contents for RST825 SatRADIO































Search results

Summary of Contents for RST825 SatRADIO

Reviews:

Related manuals for RST825 SatRADIO

Brands by name

Popular brands

Beam RST825 SatRADIO, User And Installation Manual

Search results

Summary of Contents for RST825 SatRADIO

Reviews:

Related manuals for RST825 SatRADIO

Brands by name

Popular brands