background image

19 November 2008 

BD X-Monitor 2 #

 1080500

 34 

BD Engine Brake Inc 

A10 – 33733 King Rd, Abbotsford, BC, Canada V2S 7M9 

Ship: #88 – 446 Harrison St, Sumas, WA  98295     Mail: PO Box 231, Sumas, WA 98295 

Ph: 604.853.6096   Fax: 604.853.8749   Internet: www.bd-power.com  

LIMITED WARRANTY STATEMENT 

 

BD Engine Brake, Inc., Valley Fuel Injection Ltd., BD Diesel Performance, Turbocharger.net (the “Seller”) 
warrants the following product(s):  
 
All products manufactured or rebuilt by the Seller are to be free from defects in material or workmanship which 
includes but is not limited to Turbochargers, Exhaust and Intake manifolds, Exhaust brakes, Intercoolers, Flex 
Plates, Transmissions, Torque Converters, Oil pans, Fuel pumps and systems, Electronic monitors and control 
systems.  The Seller warrants to the original buyer of the product (the “Buyer”) that it will repair or replace, free of 
charge, any product which has a defect in material or workmanship within the warranty period described below. 
Copy of original invoice is required to qualify for warranty.  
 
A defect is defined as a condition within the product that would render the product inoperable under normal 
conditions of use and service. The Seller’s responsibility under this Warranty is limited to the repair or 
replacement, at the Seller’s option, of any warrantable product returned prepaid with a complete service history 
and proof of purchase.  A valid proof of purchase is a dated bill of sale or receipt. 
 
A Return Material Authorization (RMA) number, obtained in advance from a customer service representative of 
the Seller and the dated bill of sale or receipt, must accompany any product returned by the Buyer for warranty 
determination.  The Seller will be the final authority on the approval of all warranty claims hereunder.  The 
issuance of a RMA number does not represent an approval of a warranty claim.  All repaired or replaced products 
will be returned to the Buyer freight collect.  Accepted warranty products, which have been replaced, will become 
the sole property of the Seller. 
 
Until the Seller has approved a warranty claim, the Buyer will be responsible for all costs.  Replacement parts and 
the labor costs incurred by the removal and replacement of the product while performing warranty work will be the 
responsibility of the Buyer.  In no case does the obligation of the Seller exceed the original purchase price of the 
product as indicated on the original bill of sale or receipt.  Under no circumstances will the Seller be liable for any 
travel time incurred in diagnosis for defects, or any other contingent expenses. 
 
Once the claim is approved and with in a 1 year period of original purchase Labor costs incurred will be 
considered for the removal and replacement of an eligible part while performing warranty work, at a rate of 55.00 
per hour at authorized centers with prior approval of the Seller.  Freight is FOB Abbotsford, B.C. Canada. 
 
To the extent permitted by law, the Buyer hereby waives all rights other than those expressly set out herein and 
acknowledges that this warranty sets out the Buyer’s exclusive remedies with respect to products covered by it.  
This warranty shall not be extended, amended or varied except by written instrument signed by the Seller and the 
Buyer. 
 
The Seller will administer warranty requests on products sold by the Seller and not manufactured by the Seller by 
forwarding claims made by a Buyer under the manufacturer’s warranty to the manufacturer.  The final disposition 
of such claims will be made by the manufacturer and ruled by the laws of British Columbia, Canada.  
 
Customer assumes risk in purchasing product with in 30 days may return the product for exchange of other BD 
products or services only. No cash refunds are available.  

 

Please refer to Warranty time limitation per product.

Summary of Contents for X-monitor 2





































Reviews: