background image

F/W Version 2.1 

12 

12.2.

 

AUX Mode 

 

See P5 "6.2.AUX Mode". 

12.3.

 

Wing Type 

 

See P7 "6.9.Wing Type & Mixing". 

12.4.

 

Gain Menu 

12.4.1.

 

Master Gain 

 

See P7 "6.7. Master Gain Control Channel (GAIN)". 

12.4.2.

 

Gain Adjustment for each Flight Mode 

This function is used to set the gyro gain 

of  aileron,  elevator  and  rudder  for  each 

flight  mode.  The  gain  can  be  set  from 

0%  to  100%,  the  higher  the  gain,  the 

more  stable  the  aircraft.  The  gain  is  affected  by  many  factors  there  is  no  standard  answer  to  that  how  much  it 

should be. You need to fine-tune carefully to get the best result. The aircraft will become vibrative if the gain is 

too large, you'd better start with a lower volume for your first flight and then increase it gradually. The function of 

remote master gain will make it much more convenient for changing the gain during flight. 

12.4.3.

 

Gain Ratio 

In  order  to  meet  more  needs, 

A3X Pro E.

  provides  3-level  gain  ratio  for  each  flight  mode. 

The  ratio  can  be  selected  between  Small  (S),  Medium  (M)  and  Large  (L),  default  is 

Medium which will be suitable for most aircrafts. You can choose a larger level when the 

current  gain  is  still  not  large  enough,  even  when  it  has  been  set  to  the  maximum.  But 

remember that always use as small ratio as possible to improve the precision of gain adjustment. 

12.5.

 

Mount Orientation 

As mentioned in P4 "5.Installation", you have to choose the correct mount orientation here 

after installation. Incorrect setting will result in an unexpected failure. 

 

HTTP://WWW.BAY-TEC.DE                    

                                                                                                                      Sept. 12, 2013                             

 

 

 

 

   

Summary of Contents for A3X Pro



















Reviews: