Baxi Arena Super Installation And Servicing Instructions Download | Manualshive

Page: 17 / 30

background image

Supplied By www.heating spares.co Tel. 0161 620 6677

17

Annual Servicing - Page 17

Disconnect the 3-pin plug from the socket beneath the fire.

Isolate the gas supply.

Disconnect the fire inlet pipe from the fire inlet.

HEARTH MOUNTING

Pull the fire forward until the flue spigot is clear of the closure
plate and lift away.

Inspect the fireplace for damage and blockages.

WALL FIXING

Remove and retain the screws securing the fire to the wall
mounting brackets.

Whilst holding the fire in position, remove and retain the
screws securing the fire to the backing plate. Pull the fire
forward until the flue spigot is clear of the closure plate and
lift away.

Inspect the fireplace for damage and blockages.

«
...
15
16
17
18
19
...
»

Summary of Contents for Arena Super































Reviews:

No comments

Related manuals for Arena Super

Brand: baltur Pages: 153

Brand: Napoleon Pages: 104

Brand: Ooni Pages: 19

Brand: Riello Pages: 56

Brand: Riello Pages: 56

Brand: Masport Pages: 20

Brand: Olympia Pages: 26

Brand: Riello Pages: 56

Brand: Eclipse Pages: 17

Brand: Comfort Flame Pages: 32

Brand: FBR Pages: 6

Brand: baltur Pages: 38

Brand: PROPOINT Pages: 24

Brand: PROPOINT Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands