manualshive.com logo in svg

Baumer OM70, Operating Instructions Manual

Share
Download
Baumer OM70 Operating Instructions Manual Download Page 7

 

en_BA_OM70_multi-spot.docx

 

7/60

 

Baumer Electric AG 

04.01.2021 14:26/tof V1.2 ANW_81156398

 

 

Frauenfeld, Switzerland

 

Optional settings 

OBJECT 

Selection of bright or dark objects to optimize the measurement results. 
 

PRECISION 

To achieve better precision and resolution, it is possible to alternate between Standard, High and Very High 
by filtering the output values. 
 

FIELD OF VIEW

 

The width of the measuring field can be changed with FIELD OF VIEW. Separate configuration of the single 
points of the field: LIMIT LEFT, LIMIT RIGHT. 
This function is required when there are objects in the measuring field that should not be detected. 
 

ANALOG OUT 

Start of measuring range Sdc and end of measuring range Sde can be changed with SCALE OUT. 0V or 4mA 
then apply for the start of measuring range Sdc. 10V or 20 mA apply for the point at the end of measuring 
range Sde. V

oltage and current output is selected under ANALOG OUT. In addition, the output curve can be 

inverted under OUTP. SLOPE.

 

 

DIGITAL OUT

 

The sensor is equipped with a switching output that can be configured as a threshold or as a window via the 
DIGITAL OUTPUT function. 
Threshold: As soon as the measuring value is greater than the entered threshold, the switching output will be 
changed. 
Window: As soon as the measuring value is outside the entered window, the switching output will be changed. 
 
 
 
 

Let's get started 

The sensor continuously outputs the measuring value in mm to the display and transmits it via the analog 
output to the control. Alternatively, the measuring value can also be retrieved from the RS485 interface. 

 

 

 

 

4 

Summary of Contents for OM70





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands