background image

98

CARE AND MAINTENANCE OF THE GLASS 

CERAMIC HOB

TROUBLESHOOTING GUIDE

hob not working

When pressing the control buttons, did you 

follow the instructions in the section “Using 

the hob” in the enclosed ”Product 

Description Sheet”?

Is there perhaps a power failure?

Did you dry the hob carefully after cleaning it?

1.

If a cooking zone has been selected and an 

“F” 

or an “ER” appear on the display followed 

by a number, contact the After Sales 

Service and inform them.

- With the exception of the message

 “F03”

 

or 

“ER03”

 

that identifies the incorrect 

cleaning of the controls area.

- To solve the problem follow the instructions 

in the “Cleaning and maintenance of the 

glass-ceramic hob” paragraph.

2.

If one of the following codes is displayed 

when the hob On button is pressed:

 F12, 

F13, F22, F25, F31, F36, F47, E2, E5, E6, 

E7, E9 

contact the After-sales Service and 

inform them of the code displayed.

3.

If the hob does not work following intensive 

use, the hob internal temperature is too high. 

Wait a few minutes until the hob cools down. 

The display shows the code 

“F21”

.

Important!

If you are not able to turn the glass ceramic hob off 

after using it, disconnect it immediately from the 

power supply.

Clean the hob, when it is cool, after each use. This will prevent the 

build-up of dirt and make cleaning easier.

Important:

 never clean the appliance with high pressure water or 

steam cleaning equipment.

Use a clean cloth, absorbent kitchen wipes and washing up 

liquid or a specific glass ceramic cleaner.

Remove baked-on dirt with the special scraper tool 

(if provided) and specific cleaning products.

Food spills should be cleaned off before they bake onto the 

glass ceramic surface.

Foods with high sugar content (toffee, fruit juice, jam, etc.) 

that boil over while cooking, or spattered sugar stains must be 

immediately removed using a scraper.

Do not use abrasive products, bleach, oven-cleaner spray or 

pan scourers.

The hob should be treated periodically with a proprietary brand 

of protective wax for glass ceramic hobs.

41902033GB.fm  Page 98  Monday, October 11, 2010  11:22 AM

Summary of Contents for EDPV 6740 IN









Reviews: