Bauer S300 Original Operating Manual Download

Page: 41 / 41

Operating Manual for

BAUER Separator S300

CONFORMITY DECLARATION

EC Conformity Declaration

according to EC Directive 2006/42/EC

The manufacturer

Röhren- und Pumpenwerk BAUER Gesellschaft m.b.H.

Kowaldstraße 2, 8570 Voitsberg, Austria

Tel: +43 3142 200-0; Fax: +43 3142 200-320/-340

declares that the machine named below

Machine designation

Bauer Separator

Machine type / base device

S300

correspondingly applies to the relevant provisions of the following directives.

Machinery Directive

2006/42/EC

Electromagnetic Compatibility Directive 2014/30/EU

Low Voltage Directive

2014/35/EU

The following standards in the current versions were applied correspondingly:

EN ISO 12100:2011/03

Safety of machinery -General principles for design risk assessment
and risk reduction

EN ISO 13857:2008/08

Safety of machinery

– Safety distances to prevent hazard zones

being reached by upper and lower limbs

EN 349:2008/09

Safety of machinery - Minimum gaps to avoid crushing of parts of
the human body

This declaration becomes void in event of any changes to the machine made without the ap-
proval of Bauer GmbH.

Party responsible for documentation: Thomas Theissl, Kowaldstraße 2, 8570 Voitsberg, Austria

Summary of Contents for S300










































Search results

Summary of Contents for S300

Reviews:

Related manuals for S300

Brands by name

Popular brands

Bauer S300, Original Operating Manual

Search results

Summary of Contents for S300

Reviews:

Related manuals for S300

Brands by name

Popular brands