Bauer S300 Original Operating Manual Download | Manualshive

Page: 28 / 41

background image

22

Operating Manual for

BAUER Separator S300

S

13.1.2

Sealing

The  sealing  consists  of  a  rotary  shaft  seal  running  on
the  bushing  which  is  glued on the auger hub. In addi-
tion a slide ring pretensioned by O-rings is mounted on
the auger hub. This slide ring serves as additional pro-
tection  for  the  rotary  shaft  seal.  It  is  turning  with  the
auger  and  is  sliding  on  the  wear  plate  which  is  bolted
to the housing.

When dismounting the auger, the O-rings and the slide
ring remain on the auger hub and can be pulled out of
the machine together with the auger.

When reinstalling the auger, make sure that the com-
plete auger hub (especially the glued bushing) and the
slide ring are free of dirt in order not to damage the ro-
tary shaft seal.

The surface of the slide ring which is in contact with
the wear plate during operation and also the bushing
must be greased before installation, the other surfaces
of the sealing must be free of grease

rotary shaft seal

bushing

slide ring

O-Rings

Abb.13-4 Sealing

wear plate

«
...
26
27
28
29
30
...
»

Summary of Contents for S300










































Reviews:

No comments

Related manuals for S300

Brand: Hach Pages: 4

Brand: Kärcher Pages: 60

Brand: Katadyn Pages: 2

Brand: AlkaViva Pages: 13

PWS BEV-300 Series

Brand: Pure Water Pages: 35

Brand: Clayton Pages: 16

Brand: ROSEDALE Pages: 6

100 GPD U.H.E RO/DI

Brand: SpectraPure Pages: 18

Brand: Sony Pages: 2

Brand: TriangleTube Pages: 12

Brand: Hydac Pages: 56

Brand: Viking Pages: 5

Brand: CPI Pages: 8

Brand: waatr Pages: 11

Brand: Aquaguard Pages: 5

CleanSweep AP LG Series

Brand: OnFILTER Pages: 2

CareClear Pro Series

Brand: Water Care Pages: 32

Brand: CorroVenta Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands