background image

 
 

II

 

Operating Manual for 

BAUER Separator S300

 

 

 

PRODUCT DETAILS 

 
 

Type designation: 

 

Separator 

Type number: 

 

S300 

Serial number

1

 

 

 

 

 

Dealer: 

Name: 

 

 

Address: 

 

 

 

 

 

Tel. / fax: 

 

 

 

 

Shipping date: 

 

 

 

 

 

Producer of the machine: 

 

Röhren- und Pumpenwerk 

BAUER 

Ges.m.b.H. 

 

 

Kowaldstr. 2 

 

 

A - 8570 Voitsberg 

 

 

Tel.: +43  3142  200 - 0 

 

 

Fax: +43  3142 200 

–320 /-340 

 

 

e-mail: [email protected] 
www.bauer-at.com 
 

Owner or operator: 

Name: 

 

 

Address: 

 

 

 

 

 

Tel. / Fax: 

 

 
 
 
 

Note:  Make  a  note  of  the  type  designation  and  serial  number  of  your  separator  and  its  accessories.  In-
clude these numbers along with all contact with your dealer. 
 

                                                      

1

 It is very important to include with all guarantee claims and all correspondence related with this machine 

the entire serial number group, including all letters, both for the machine and for its relevant components. 
This point cannot be stressed enough. 

 
 

Summary of Contents for S300










































Reviews: