26
Connect the metal structure of the appliance to the equipoten-
tial node. Connect the conductor to the terminal with the
symbol
on the outside part of the bottom.
9.4 CONNECTION TO THE WATER SUPPLY
The appliance must be connected to a potable water supply.
The water inlet pressure must be between 150 kPa and 300
kPa. Use a pressure reducer if the inlet pressure is above the
maximum permitted level.
• Install a mechanical fi lter and a shut-off valve upstream of
the appliance in an easily accessible point.
• Make sure the water circuit is free from ferrous particles befo-
re connecting the fi lter and the appliance.
• Seal any unused connectors with a plug.
• Once the appliance has been installed, check for gas leaks at
the connection points.
9.5 CONNECTION TO THE WATER DRAIN
The water drainage system must be provided using materials
resistant to temperatures of 100 °C. The bottom of the applian-
ce must not be subjected to steam produced by drainage of
hot water.
10 CONVERSION TO A DIFFERENT TYPE OF GAS
Table T1 specifi es, for each country:
• which gas can be used for the appliance
• the nozzles and settings for each gas that can be used For
nozzles, the number indicated in table T1 is also stamped on
the nozzle body.
To convert the appliance to the local gas type, follow the in-
structions given in a table T1 and carry out the steps below :
• Replace the main burner nozzle ( UM ).
• Adjust the main burner's air regulator to distance A.
• Replace the pilot burner nozzle ( UP ).
• Adjust the pilot burner air fl ow (if necessary).
• Replace the gas valve minimum nozzle ( Um ).
• Affi x the adhesive tab indicating the new type of gas used.
The nozzles and adhesive tabs are supplied with the applian-
ce.
10.1 GAS
FRY-TOP
10.1.1 REPLACING THE MAIN BURNER NOZZLE AND
ADJUSTING THE PRIMARY AIR FLOW
• Remove the control panel.
• Loosen the screws V1.
• Remove the nozzle-support manifold.
• Remove nozzle UM and replace it with the one indicated in
table T1.
• Retighten nozzle UM.
• Slacken screw V and position the air regulator at distance A
as indicated in table T1.
• Retighten screw V fully.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
10.1.2 REPLACING THE MINIMUM
ADJUSTMENT
SCREW
• Remove the control panel.
• Remove nozzle UM and replace it with the one indicated in
table T1.
• Retighten nozzle UM.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
10.1.3 REPLACING THE PILOT BURNER NOZZLE
• Remove the control panel.
• Undo connector R.
• Remove nozzle UP and replace it with the one indicated in
table T1.
• Retighten the connector R. Re-assemble all parts.
• For assembly, proceed in reverse order.
11 COMMISSIONING
See Chapter " INSTRUCTIONS FOR MAINTENANCE "
INSTRUCTIONS FOR USE
REMINDERS FOR THE USER
The manufacturer will not be liable for any damage or in-
jury resulting from failure to observe the following rules
• Read this manual carefully. It provides important information
for safe installation, use and maintenance of the appliance.
• Keep this manual in a safe place known to all users so that it
can be consulted throughout the working life of the appliance.
• Installation, conversion to a different type of gas and applian-
ce maintenance must be carried out by qualifi ed technicians
authorized by the manufacturer, in compliance with current
safety standards and the instructions in this manual.
• For after-sales service, contact technical assistance centers
authorized by the manufacturer and demand the use of origi-
nal spare parts.
• Have the appliance serviced at least twice a year. The manu-
facturer recommends taking out a service contract.
• The appliance is designed for professional use and must be
operated by trained personnel.
• The appliance is to be used for cooking food as specifi ed
in the reminders for use. Any other use must be considered
improper
• Do not allow the appliance to operate empty for prolonged
periods. Only pre-heat the oven just before use.
• Do not leave the appliance unattended while in operation.
• In the event of an appliance fault or malfunction, shut the
gas shut-off valve and/or switch the appliance off at the main
switch installed upline.
• Clean the appliance following the instructions given in Chap-
ter " INSTRUCTIONS FOR CLEANING".
• Do not store fl ammable materials in close proximity to the
appliance. FIRE HAZARD.
• Children should be supervised to ensure that they do not
play with the appliance.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabili-
ties, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Do not obstruct any air vents or drains present on the ap-
pliance.
• Do not tamper with appliance components.
12 USING THE GAS FRY-TOP
REMINDERS FOR USE
• The appliance is designed for cooking foods directly on the
hotplate ( steaks, hamburgers, fi sh, vegetables, etc.).).
• The hotplate must not be used to heat pans or saucepans.
• Empty the grease collection tray several times a day.
• Exercise great caution when removing the tray. DANGER of
scalding from hot oil.
Summary of Contents for SERIE 650 SNACK
Page 5: ...4 FIGURE ABB FIG ...
