![background image](http://html1.mh-extra.com/html/consort/trf25c-lst/trf25c-lst_installation-and-operating-instructions_2655166001.webp)
46000134 Iss 04
SAFETY
When using any electrical appliance, basic safety precautions should always be observed.
Please read these instructions carefully and retain for future use.
The appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety. Young children should be supervised to ensure
that they do not play with the appliance.
This appliance is intended to dry towels and therefore is hot to the touch. Any rise
in ambient temperature is directly reflected in the appliance, and as a result of this
the appliance will feel hotter to the touch during warmer periods. Also the
insulation effect of towels will cause the operating temperature to increase slightly.
The avoid a hazard this heated towel rail
MUST NOT
be used to carry towels or any
other articles that have been in contact with oil, petroleum based products or dry
cleaning fluids.
Use this appliance only on the voltage specified on the rating label.
Do
NOT
use this towel rail unless it has been fitted to the wall as per these
instructions.
Do
NOT
immerse in any liquid.
Do
NOT
allow the supply cable to come into contact with heated surfaces during
operation.
The towel rail and flexible cable outlet must be mounted so that no part of them can
be touched by any person using a bath or shower.
Do NOT use the appliance if damaged.
SPECIFICATIONS
DIMENSIONS
Model:
TRF30 LST
TRF25C/LST/TRJ40/TRJ40C
TRJ60/TRJ60C
TRJ80
Width:
465mm
465mm
495mm
540mm
Height:
425mm
415mm
665mm
875mm
Depth:
86mm
86mm
86mm
86mm
Weight:
1.4 kg
1.5 kg
1.9 kg
2.6 kg
ELECTRICAL
Wattage:
27-30 W
23-25 W /42-45 W
60-65 W
84-85 W
Supply:
230-240 Volts ac 50 Hz, single phase
Ingress Protection Rating: IP34 – Splashproof – Double Insulated
This towel rail meets the requirements of EU Directive 89/336/EEC
(Amended by 92/31/EEC) for Electromagnetic Compatibility.
Please note, the
TRF25C LST &
TRF30 LST
are
Low Surface Temperature
models which have a
maximum surface temperature of 43
0
C when uncovered
to comply with Department of Health
guidelines.
The surface temperature of the rail beneath a towel can exceed this temperature.
INSTALLATION
Ensure the electricity supply is disconnected from any relevant fixed wiring before
commencing the installation.
This appliance MUST be connected in accordance with the latest IEE regulations and
fitted by a competent electrician. The supply circuit must be adequate for the input of
the appliance. The towel rail must be connected via a fused, double pole, switched
(having a contact separation of at least 3mm in each pole), flexible cable outlet and
fitted with a 3 Amp fuse or via a plug and socket.
When installed in a bathroom, the towel rail must
NOT
be connected via a plug and
socket. The towel rail must also be located in the appropriate zone of the bathroom, in
accordance with section 601 of the Wiring Regulations BS 7671:1992 (Amendment 10983).
NOTE: This class II appliance does NOT require earthing.
MOUNTING
PROCEDURE
Choose a suitable position on the wall to mount
the heated towel rail. The cable entry can be
either on the left or right hand side, but it must be
horizontal and at the bottom of the frame.
WARNING:
In order to avoid a hazard for young
children, the wall mounted towel rails must be
installed so that the lowest heated rail is at least
600 mm above the floor.
1.
Swivel the leg brackets around so they are
angled at 90
0
to the rear of the frame.
2.
Place the towel rail on a flat surface, check
that all the leg brackets are sitting parallel and
then tighten the tube clamp screws sufficiently
that the tube clamp sits flush into the wall
fixing bracket, but do not over-tighten.
3.
Level up the top rail of the heated towel rail
and fasten to the wall with either the screws
provided or other suitable fixings.
4.
Fit the screw caps
to cover the screw
holes in each leg
bracket.