background image

Safety 

Ex p relay 

Power 

 

Page 12 of 24 

Rev. 0 

20190910_Manual_Exp-Relais_Power_en.docx 

 

Marking and test certificate 

The relay is approved for the following areas 

 

ATEX (Europe) 

17-51P6-1*11/**** 

Marking  

 II 2G Ex eb qb IIC T4 Gb 

 II 2D Ex tb IIIC T130 °C Db 

Test certificate 

EPS 18 ATEX 1159 X 

IECEx (International) 

17-51P6-1*11/**** 

Marking 

Ex eb qb IIC T4 Gb 
Ex tb IIIC T130 °C Db 

Test certificate 

IECEx EPS 18.0082X 

 

 

Avoidance of damage to property 

 

 

Short circuit due to improper connection  

 

An incorrect connection of the power supply will destroy the electronics and void 
the warranty. 

 

 

Storage at an excessively high temperature  

 

Store the Ex p control unit at the intended storage temperature since otherwise 
damage to the electronics or seals may occur. Ensure adequate air conditioning 
at high storage temperatures. 

 

 

Aggressive cleaning agents 

 

When selecting the correct cleaning agent, it is essential that it is suitable for 
use since otherwise damage may occur to seals and connections. Combustible 
products are generally not permitted. 

 

 

Danger to health due to improper disposal 

 

According to the European WEEE Directive, electrical and electronic equipment 
may not be disposed of with household waste. Their components must be sent 
separately for recycling or disposal because toxic and hazardous components 
can cause long-term damage to health and the environment if not disposed of 
properly. 

As consumers, you are obliged under the Electrical and Electronic Equipment Act 
(ElektroG) to return electrical and electronic equipment at the end of its 
serviceable life free of charge to the manufacturer, the point of sale or to public 
collection points set up for this purpose. Details of this are regulated by the 
respective national law. The symbol on the product, the operating instructions 
or/and the packaging refers to these regulations. With this type of material 
separation, recycling and disposal of old devices, you make an important 
contribution to the protection of our environment. 

 

Summary of Contents for 17-51P6-1 11 Series



























Reviews: