Barnett Engineering PRO TALK CV2 Page 4 Instruction Manual Download | Manualshive

Page: 4 / 61

background image

B1272M001

BARNETT ENGINEERING LTD.

ProTalk Cv2

Regulatory Notices

CAUTION
The ProTalk Cv2, model B1272D, has been certified by the Federal Communications
Commission (“FCC”) using the included articulating dual-band dipole antenna. Unauthorized
modifications or changes not expressly approved by Barnett Engineering Ltd. could void
compliance with regulatory rules, and thereby your authority to use this equipment.

ANTENNA CONSIDERATIONS
The included articulating dual-band dipole antenna installation must provide a separation
distance of 20 cm (8") or more between the antenna and all persons to satisfy Maximum
Permissible Exposure (MPE) compliance.

INTERFERENCE TO MEDICAL DEVICES
The ProTalk Cv2, model B1272D, contains an embedded cellular telephone module. Do not use
this device in health care facilities where cellular phone use is restricted.

Interference to pacemakers, hearing aids, and other medical or personal electronic devices may
occur. Consult the manufacturer of those devices to determine if they are adequately shielded
from external RF energy. Your physician may be able to assist you in obtaining this information.

POTENTIALLY UNSAFE AREAS
Do not use this device in any area or facility where posted notices restrict the use of cellular
phones.

FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which the user will be required to correct the interference at his own expense.

INDUSTRY CANADA COMPLIANCE
This Class A digital device complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à norme NMB-003 du Canada.

IDENTIFICATION:
FCC ID:

OVFKWC-M200

Industry Canada ID:

IC:3572A-M200

«
...
2
3
4
5
6
...
»

Summary of Contents for PRO TALK CV2






























































Reviews:

No comments

Related manuals for PRO TALK CV2

Brand: Ultra Start Pages: 20

Brand: ZEBON Pages: 2

Brand: FAAST Pages: 12

Brand: Bellman & Symfon Pages: 4

Brand: TFA Pages: 18

Brand: Olympia Pages: 40

Brand: Salora Pages: 12

Brand: DeWalt Pages: 40

Brand: DeWalt Pages: 2

Brand: Autostart Pages: 10

Brand: By Firstech Pages: 14

Brand: AUTHOR Alarm Pages: 48

Brand: AUTHOR Alarm Pages: 44

JBL Premium sound

Brand: Toyota Pages: 47

SMD-429 PG2 Series

Brand: Visonic Pages: 9

Brand: Silencer Security Systems Pages: 4

Brand: Prestige Pages: 8

Brand: DAITEM Pages: 124

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands