Barnett Engineering PRO TALK CV2 Instruction Manual Download

Page: 57 / 61

Specifications

8-2

B1272M001

BARNETT ENGINEERING LTD.

ProTalk Cv2

intervals are adjustable from 1 to 249 minutes; the short
timer can be used from 1 to 9 times.

Acknowledge Code

• Stops the transmission cycle when received. 1 to 7 DTMF

digits with individual codes allowed for each group.

Interrogate Code

• Forces annunciation of all active alarms; analog levels,

totalizer readings and interval timers. 1 to 7 DTMF digits
with individual codes allowed for each group.

8.3 Telephone

Directory Structure

• Up to 20 numbers in each of the 6 directories; each

directory can hold up to 200 digits.

Access

• Multiple methods of security are available to restrict access

and to control the unit.

8.4 Options

Packaged model

• NEMA 4 enclosure

• Battery-backed power supply

• Programming telephone set

Summary of Contents for PRO TALK CV2






























































Search results

Summary of Contents for PRO TALK CV2

Reviews:

Related manuals for PRO TALK CV2

Brands by name

Popular brands

Barnett Engineering PRO TALK CV2, Instruction Manual

Search results

Summary of Contents for PRO TALK CV2

Reviews:

Related manuals for PRO TALK CV2

Brands by name

Popular brands