manualshive.com logo in svg

BARIX Annuncicom, User Manual

Share
Download
BARIX Annuncicom User Manual Download Page 44

Annuncicom

 User Manual Version 4.07

IO settings

The 

I1

 pushed command r=192.168.0.20/c=80 will activate the relay on the control station for the Relay 

toggle duration time set in the control station when the RING button is pressed on the door station panel.

The 

I1

 released command has to be blank.

Adjust the Relay toggle duration according to the specification of the door strike used.

All other commands are not used and can be left blank or as is.

Security settings

These settings need not to be changed for now. 

Adjust them later according to your security needs.

8.2.2 Control station configuration

Lets take a look on how to configure the control station.

Wiring

The control station is connected to an intercom panel: Speaker to speaker out (C). 

Microphone to Microphone In (E or F).

The TALK button to Input 0 (B1 and B3).  

The DOOR button to Input 1 (B2 and B3).  

The flash or buzzer to Relay normally open (B4) and Relay common (B5).

Network settings

SonicIP is disabled, no need to hear it on power up as the IP is static and known and will not be power 

cycled anyway.

BARIX AG

 | 28. Jan. 2014 | Application notes | Page 44/54

Summary of Contents for Annuncicom























































Reviews:

No comments

Brands by name

Popular brands

Load more brands