Barco X8 Installation Manual Download Page 35

Page: 35 / 96

6. Setup process of a X8 rental display

6. SETUP PROCESS OF A X8 RENTAL DISPLAY

About this chapter

This chapter roughly describes the installation process of the X8 rental display for a base stand (

oor mount) or truss (hanging)

con

guration. Several process stages refer to one or more of the detailed "Basic setup procedures", page 39.

Floor mount or hanging X8 rental display

The X8 rental tiles can be used in a

oor mount or in a hanging rental con

guration. These con

gurations are limited in height,

maximum 3 tiles high for a

oor mount and maximum 13 tiles high for a hanging con

guration. Furthermore, a

oor mount (base

stand) con

guration can only be used indoor and must be equipped with a stacker support system at the rear of the display.

ARNING

Safety

rst. Fence off the installation area before starting to install your X8 rental display. Ensure

you read, understand and follow all safety instructions mentioned in the chapter "Safety", page 3, of this
installation manual. Furthermore, make sure that all installation requirements for your X8 rental display are
ful

lled, see chapter "Installation requirements", page 11.

AUTION

Cover up the LED-wall on-site, to protect from dust and dirt, until the start of the event.

Overview

•

Set up a

oor mount X8 rental display

•

Set up a hanging X8 rental display

R5905160 X8 RENTAL DISPLAY 25/02/2013

Summary of Contents for X8

































































































Search results

Summary of Contents for X8

Reviews:

Related manuals for X8

Brands by name

Popular brands

Barco X8, Installation Manual

Search results

Summary of Contents for X8

Reviews:

Related manuals for X8

Brands by name

Popular brands