Barco X8 Installation Manual Download Page 30

Page: 30 / 96

5. X8 rental peripherals and accessories

5.3

X8 rental

ight cases

X8 rental

ight case for 3 X8 rental tiles

The X8 rental

ight case holds up to 3 X8 rental tiles. The X8 rental tiles are placed vertically into the base of the

ight case. The

X8 rental tiles have to be placed one by one into the

ight case with the LEDs facing the full wooden plate (without hole). Then a

wooden plate with hole is placed after the last X8 rental tile. On top of the three X8 rental tiles a

xation plate is placed to secure

the tiles. To make the

ight case easy to handle it is provided with castor wheels, handles and stacking dishes.

Image 5-3

X8 rental

ight case for X8 truss beams and/or rental feet

This X8 rental

ight case is multifunctional. It can hold 4 X8 rental feet, or 4 X8 single truss beams, or 2 X8 dual truss beams, or a

combination of rental feet and truss beams. To make the

ight case easy to handle it is provided with castor wheels, handles and

stacking dishes.

Image 5-4

ARNING

Maximum stack two (2)

ight cases with X8 Rental Tiles high and three (3)

ight case with X8

feet/truss accessories high X8 rental

ight cases high. Never higher.

R5905160 X8 RENTAL DISPLAY 25/02/2013

Summary of Contents for X8

































































































Search results

Summary of Contents for X8

Reviews:

Related manuals for X8

Brands by name

Popular brands

Barco X8, Installation Manual

Search results

Summary of Contents for X8

Reviews:

Related manuals for X8

Brands by name

Popular brands