Barco TF-20 Service Manual Download

Page: 58 / 95

7. Tile reassembling

7.1

Reassembling an external fan + dust

lter

Necessary tools

Cross head screw driver.

External fan and dust

lter

A dust

lter is located underneath the external fan. Always check the status of the dust

lter before replacing the external fan.

Image 7-1

ARNING

Replacing a malfunctioning external fan does not mean you need to replace the dust

lter. Al-

though it is strongly recommended to clean the dust

lter before reassembling it. To clean a dust

lter, use

compressed air to blow out the gathered dirt.

How to insert a dust

lter and an external fan?

1. Place the dust

lter underneath the external fan and position both components in place.

2. Connect the power cable.

Image 7-2

3. Fasten the four indicated screws.

R59770270 TF-20 21/05/2008

Summary of Contents for TF-20
































































































Search results

Summary of Contents for TF-20

Reviews:

Related manuals for TF-20

Brands by name

Popular brands

Barco TF-20, Service Manual

Search results

Summary of Contents for TF-20

Reviews:

Related manuals for TF-20

Brands by name

Popular brands