Barco Coronis 5MP Mammo Getting Started Manual Download Page 25

Page: 25 / 88

Display parts, controls and connectors

Rear view

Figure 2: Rear side

Connector compartment cover

To get access to the connectors, remove the cover by pulling
down the 2 clips at the top of the cover.

Tilt & swivel foot cover

This cover is packed in a separate box when the display is
shipped to the customer.

Tilt & swivel foot

DC power input

Connect the external power supply, delivered with the display,
to this connector.

+5 Vdc, 0.25 A power output for accessories.

DVI (digital) video input

Slot for security cable (e.g., Kensington lock)

USB upstream port

Connect this connector to the PC USB bus if you wish to connect
USB devices to the display’s USB downstream port.

8 9

Summary of Contents for Coronis 5MP Mammo

























































































Search results

Summary of Contents for Coronis 5MP Mammo

Reviews:

Related manuals for Coronis 5MP Mammo

Brands by name

Popular brands

Barco Coronis 5MP Mammo, Getting Started Manual

Search results

Summary of Contents for Coronis 5MP Mammo

Reviews:

Related manuals for Coronis 5MP Mammo

Brands by name

Popular brands