Barco Coronis 5MP Mammo Getting Started Manual Download Page 19

Page: 19 / 88

Explanation of symbols

Explanation of symbols

Symbols on the display and / or power supply

On the display or power supply, you may find the following symbols
(nonrestrictive list):

Indicates compliance to the essential require-
ments of the Directive 93/42/EEC

Indicates compliance with Part 15 of the FCC
rules (Class A or Class B)

Indicates the display is approved according to
the UL regulations

Indicates the display is approved according to
the c-UL regulations

Indicates the display is approved according to
the DEMKO regulations

Indicates the display is approved according to
the CCC regulations

Indicates the USB connectors on the display

Indicates the manufacturing date

Indicates the temperature limitations for the
display to operate within specs

Summary of Contents for Coronis 5MP Mammo

























































































Search results

Summary of Contents for Coronis 5MP Mammo

Reviews:

Related manuals for Coronis 5MP Mammo

Brands by name

Popular brands

Barco Coronis 5MP Mammo, Getting Started Manual

Search results

Summary of Contents for Coronis 5MP Mammo

Reviews:

Related manuals for Coronis 5MP Mammo

Brands by name

Popular brands