5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION SET UP
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION SET UP
4-7
IN
S
T
ALLATI
O
N
S
E
T
UP
4-7
IN
S
T
ALLATI
O
N
S
E
T
UP
After scan inversion, close the chassis and close the top cover. Reconnect the
power cord to the wall outlet.
Note
Switching over from floor to ceiling or vice versa requires a complete readjustment of
picture geometry and convergence.
Check of the correct connector position
Note : this check procedure can only be done after power (mains) connection. So, first
continue with the projector set up and the connections and then return to this checking
procedure.
Switch on the BARCOVISION 701 MULTIMEDIA and press ADJUST to start up the
adjustment mode. Select with the control disk 'Service' and press ENTER. The
service menu will be displayed. Select 'PROJECTOR SET UP' and press ENTER.
Select 'IDENTIFICATION' and press ENTER. On this screen, information is given
about the projectors configuration.
Configuration when leaving the factory : ceiling/front configuration.
Follow next procedure to check the configuration :
- switch on the projector.
- the projector starts up on the last
selected source.
- press the ADJUST key.
- highlight 'service' with the control
disk and press ENTER.
ADJUSTMENT MODE
Select a path from
below:
Select with or
then <ENTER>
<EXIT> to return
source 1
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
The 'service mode menu' will be dis-
played
- select with the control disk 'Projector
set up' and press ENTER.
Select with or
then <ENTER>
<EXIT> to return.
SERVICE MODE
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
After scan inversion, close the chassis and close the top cover. Reconnect the
power cord to the wall outlet.
Note
Switching over from floor to ceiling or vice versa requires a complete readjustment of
picture geometry and convergence.
Check of the correct connector position
Note : this check procedure can only be done after power (mains) connection. So, first
continue with the projector set up and the connections and then return to this checking
procedure.
Switch on the BARCOVISION 701 MULTIMEDIA and press ADJUST to start up the
adjustment mode. Select with the control disk 'Service' and press ENTER. The
service menu will be displayed. Select 'PROJECTOR SET UP' and press ENTER.
Select 'IDENTIFICATION' and press ENTER. On this screen, information is given
about the projectors configuration.
Configuration when leaving the factory : ceiling/front configuration.
Follow next procedure to check the configuration :
- switch on the projector.
- the projector starts up on the last
selected source.
- press the ADJUST key.
- highlight 'service' with the control
disk and press ENTER.
ADJUSTMENT MODE
Select a path from
below:
Select with or
then <ENTER>
<EXIT> to return
source 1
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
The 'service mode menu' will be dis-
played
- select with the control disk 'Projector
set up' and press ENTER.
Select with or
then <ENTER>
<EXIT> to return.
SERVICE MODE
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
Summary of Contents for BarcoVision R9000740
Page 4: ...TABLE OF CONTENTS 5975248 BARCOVISION 701 MULTIMEDIA 070597 i II TABLE OF CONTENTS ...
Page 12: ...5975248 BARCOVISION 701 MULTIMEDIA 090497 SAFETY INSTRUCTIONS 1 8 SAFETY INSTRUCTIONS ...
Page 34: ...PROJECTOR SET UP 5975248 BARCOVISION 701 MULTIMEDIA 070597 5 4 PROJECTOR SET UP ...
Page 40: ...5975248 BARCOVISION 701 MULTIMEDIA 090497 POWER CONNECTION 6 6 POWER CONNECTION ...