INSTALLATION ADJUSTMENTS
5975248 BARCOVISION 701 MULTIMEDIA 070597
INSTALLATION ADJUSTMENTS
5975248 BARCOVISION 701 MULTIMEDIA 070597
7-14
IN
S
T
ALLATI
O
N
ADJ
U
S
T
ME
NTS
7-14
IN
S
T
ALLATI
O
N
ADJ
US
TME
N
TS
CRT projection angle adjustment
The projection angle of the red and blue CRT's is dependent on the desired size
of the projected image. If the centers of green, blue and red do not coincide, the
CRT projection angle must be adjusted. Never try to correct this misalignment with
the shift correction or the static convergence controls. These controls may only be
applied to correct small errors which cannot be corrected by the CRT angle
adjustment.
CRT PROJECTION ANGLE
ADJUSTMENT
<ENTER> to continue
<EXIT> to return
DURING THIS PROCEDURE,
RED ON GREEN AND THEN
BLUE ON GREEN CROSSHAIRS
WILL BE DISPLAYED
TO ALLOW THE RED AND
BLUE CRTS TO BE ALIGNED
WITH THE GREEN CRT.
LOOSEN BOLTS A AND B
TO PIVOT THE RED CRT,
AND BOLDS C AND D
TO PIVOT THE BLUE CRT.
Ensure that the rasters are centered
on the CRT face.
Press ENTER to start the CRT angle
adjustment procedure. A crosshairs
(green and red) will be displayed on
the screen.
CRT PROJECTION ANGLE
ADJUSTMENT
<ENTER> to read more
<EXIT> to return
CRT PROJECTION ANGLE IS
THE FIRST STEP OF STATIC
CONVERGENCE ADJUSTMENT.
IT IS CRITICAL THAT THE
RASTERS ARE CENTERED ON
THE CRT FACE PLATES
PRIOR TO PERFORMING
THIS STEP.
...
ENTER continues to the crosshairs
alignment.
EXIT returns to raster shift adjustment
ADJUST returns to operational mode.
ENTER continues with the second part
of the CRT projection angle adjust-
ment.
EXIT returns to Raster shift adjust-
ment.
CRT projection angle adjustment
The projection angle of the red and blue CRT's is dependent on the desired size
of the projected image. If the centers of green, blue and red do not coincide, the
CRT projection angle must be adjusted. Never try to correct this misalignment with
the shift correction or the static convergence controls. These controls may only be
applied to correct small errors which cannot be corrected by the CRT angle
adjustment.
CRT PROJECTION ANGLE
ADJUSTMENT
<ENTER> to continue
<EXIT> to return
DURING THIS PROCEDURE,
RED ON GREEN AND THEN
BLUE ON GREEN CROSSHAIRS
WILL BE DISPLAYED
TO ALLOW THE RED AND
BLUE CRTS TO BE ALIGNED
WITH THE GREEN CRT.
LOOSEN BOLTS A AND B
TO PIVOT THE RED CRT,
AND BOLDS C AND D
TO PIVOT THE BLUE CRT.
Ensure that the rasters are centered
on the CRT face.
Press ENTER to start the CRT angle
adjustment procedure. A crosshairs
(green and red) will be displayed on
the screen.
CRT PROJECTION ANGLE
ADJUSTMENT
<ENTER> to read more
<EXIT> to return
CRT PROJECTION ANGLE IS
THE FIRST STEP OF STATIC
CONVERGENCE ADJUSTMENT.
IT IS CRITICAL THAT THE
RASTERS ARE CENTERED ON
THE CRT FACE PLATES
PRIOR TO PERFORMING
THIS STEP.
...
ENTER continues to the crosshairs
alignment.
EXIT returns to raster shift adjustment
ADJUST returns to operational mode.
ENTER continues with the second part
of the CRT projection angle adjust-
ment.
EXIT returns to Raster shift adjust-
ment.
Summary of Contents for BarcoVision R9000740
Page 4: ...TABLE OF CONTENTS 5975248 BARCOVISION 701 MULTIMEDIA 070597 i II TABLE OF CONTENTS ...
Page 12: ...5975248 BARCOVISION 701 MULTIMEDIA 090497 SAFETY INSTRUCTIONS 1 8 SAFETY INSTRUCTIONS ...
Page 34: ...PROJECTOR SET UP 5975248 BARCOVISION 701 MULTIMEDIA 070597 5 4 PROJECTOR SET UP ...
Page 40: ...5975248 BARCOVISION 701 MULTIMEDIA 090497 POWER CONNECTION 6 6 POWER CONNECTION ...
