Banner DXM1200-X2, Instruction Manual

Page: 79 / 83

February 02, 2024
DXM1200-X2 Controller Instruction Manual
© Banner Engineering Corp. All rights reserved.
79
Contains FCC ID: [UE3RM1809 or UE3SX7023EXT]
Contains IC: [7044A-RM1809 or 7044A-SX7023EXT]
HVIN: [RM1809 or 223150]
This device complies with Part 15 of the FCC Rules. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation is subject to the following two conditions: 1) This device may not cause harmful interference; and
2) This device must accept any interference received, including interference that may cause undesired operation.
Antenna WARNING: This device has been tested with Reverse Polarity SMA connectors with the antennas listed in "Certified
Antennas for 900 MHz" on page 79 . When integrated into OEM products, fixed antennas require installation preventing end-
users from replacing them with non-approved antennas. Antennas not listed in the tables must be tested to comply with FCC
Section 15.203 (unique antenna connectors), FCC Section 15.247 (emissions), and ISED RSS-Gen Section 6.8.
FCC and ISED Approved Antennas
WARNING: Antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all
persons.
AVERTISSEMENT : Les antennes utilisées pour cet émetteur doivent être installées de manière à assurer une distance de
séparation d'au moins 20 cm de toutes les personnes.
NOTICE: This equipment is approved only for mobile and base station transmitting devices. The antenna(s) used for this
transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-
transmitter product procedures.
The radio transmitter modules RM1809 and SX7023EXT have been approved by FCC and ISED Canada to operate with the
antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a
gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Certified Antennas for 900 MHz
Model Number Antenna Type 900 MHz Radio Module Maximum Gain Impedance
Minimum Required
Cable/Connector Loss
- Integral Antenna RM1809 Unity gain 0
BWA-9O1-x Omni, 1/4 wave dipole RM1809 ≤2 dBi 50 Ω 0
BWA-9O2-C Omni, 1/2 wave dipole, Swivel RM1809 or SX7023EXT ≤2 dBi 50 Ω 0
BWA-9O6-A
Omni Wideband, Fiberglass
Radome
RM1809 ≤8.2 dBi 50 Ω 2.2 dB
BWA-9O5-B Omni Base Whip RM1809 ≤7.2 dBi 50 Ω 1.2 dB
BWA-9Y10-A Yagi RM1809 ≤10 dBi 50 Ω 4 dB
BWA-9O5-C Coaxial sleeve SX7023EXT ≤5 dBi 50 Ω 0
BWA-9O6-AS Omni SX7023EXT ≤6 dBi 50 Ω 0
FCC and ISED Certification for 2.4 GHz
This equipment contains transmitter module DX80-2400 or SX243.
Radio Module DX80-2400 Radio Module SX243
FCC ID: UE300DX80-2400 FCC ID: UE3SX243
Continued on page 80