Banner DF-G1 Expert Manual Download | Manualshive

Page: 18 / 27

background image

For Sales and Support, Contact Walker EMD • Toll-free: (800) 876-4444 • Tel: (203) 426-7700 • Fax: (203) 426-7800 • www.walkeremd.com

Calibration SET

SET Button

0.04 seconds < "Click" < 0.8 seconds

Remote Input

0.04 seconds < T < 0.8 seconds

Result

Note: TEACH Selection must be programmed to CAL SEt (see

Enter Ad-

just Mode

• Set Mode switch to ADJ

No action required; sensor is
ready for Calibration SET meth-
od

Display: Red - Signal Level;
Green - Threshold

SET Sens-
ing Condi-

tion

• Present sensing condition
• Click the SET rocker but-

ton

• Present sensing condition
• Single-pulse the remote in-

put

T

Threshold Condition Accep-
ted
Displays read "cAL SEt" then
flashes "PASS"; Sensor re-
turns to Adjust mode

Threshold Condition Unac-
ceptable
Displays read "cAL SEt" then
flashes "FAIL"; Sensor returns
to Adjust mode

Return to

RUN Mode

• Move Mode switch to RUN No action required; sensor re-

turns to RUN mode automati-
cally

Display: Red - Signal Level;
Green - Threshold

DF-G1 - Expert Dual Display Fiber Amplifier Manual

18

www.bannerengineering.com - tel: 763-544-3164

P/N 161999 Rev. A

«
...
16
17
18
19
20
...
»

Summary of Contents for DF-G1 Expert




























Reviews:

No comments

Related manuals for DF-G1 Expert

Brand: Panasonic Pages: 116

Toughbook CF-T7BWATAAM

Brand: Panasonic Pages: 12

Brand: Jeep Pages: 7

Brand: Data Aire Pages: 82

Brand: Fantasea Pages: 18

Brand: Fantasea Pages: 15

Brand: M-S Cash Drawer Pages: 2

Brand: M-Audio Pages: 61

KOOLZONE SAC-1800

Brand: UNINEX Pages: 5

Brand: Panasonic Pages: 2

HighLine ABF0166

Brand: Mactronic Pages: 2

Brand: OBO Bettermann Pages: 2

Brand: hepco & becker Pages: 4

Brand: Insignia Pages: 2

Brand: PolyScience Pages: 14

Brand: Thermador Pages: 20

Brand: SR Suntour Pages: 10

Sagewash Sanitizer

Brand: Sage Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands