manualshive.com logo in svg

Banner DF-G1 Expert, Manual

Share
Download
Banner DF-G1 Expert Manual Download Page 20

For Sales and Support, Contact Walker EMD • Toll-free: (800) 876-4444 • Tel: (203) 426-7700 • Fax: (203) 426-7800 • www.walkeremd.com

Specifications

Sensing Beam

660 nm visible red

Supply Voltage

10 to 30V dc (10% max ripple)

Power and Current Consumption (exclusive of load)

Standard display mode: 960 mW, Current consump-
tion < 40 mA @ 24V dc
ECO display mode: 720 mW, Current consumption <
30 mA @ 24V dc

Supply Protection Circuitry

Protected against reverse polarity, over voltage, and
transient voltages

Delay at Power Up

500 milliseconds max.; outputs do not conduct during
this time

Output Configuration

1 current sourcing (PNP) or 1 current sinking (NPN)
output, depending on model

Output Rating

100 mA max. load (derate 1 mA per °C above 30° C)
OFF-state leakage current: < 5 μA at 30V dc
ON-state saturation voltage: NPN: < 1.5V; PNP: <
2V

Output Protection

Protected against output short-circuit, continuous over-
load, transient over-voltages, and false pulse on power
up

Output Response Time

High Speed - 200 us
Standard - 500 us
Long Range - 2 ms
Extra Long Range - 5 ms

Repeatability

High Speed - 66 us, Standard/Long Range/Extra Long
Range - 100 us

Connections

PVC-jacketed 2 m or 9 m (6.5' or 30') 4-wire integral
cable or integral 4-pin Pico-style QD or Pico-style 150
mm (6") pigtail QD or Euro-style 150 mm (6") pigtail
QD

Indicators

Red 4-digit Display: Signal Level
Green 4-digit Display: Threshold
(In Program Mode, Red and Green displays are used
for programming menus)
Yellow LED: Output conducting

Construction

Black ABS/polycarbonate alloy (UL94 V-0 rated) hous-
ing, clear polycarbonate cover

Adjustments

3-way RUN/PRG/ADJ Mode Switch
2-way LO/DO Switch
3-way +/SET/- Rocker Button

• Expert-style teaching (Two-Point and Dynamic

TEACH, Light/Dark/Window/Calibration SET)

• Manually adjust sensitivity (from "+" and "-" rocker

button only)

• Response Speed, TEACH Selection, Offset Per-

cent, Auto Thresholds, Delays/Timers, Display
Readout, Gain Selection, Factory Defaults (from
top panel or remote input)

• Top panel interface lockout (from remote input on-

ly)

Factory Default Settings:

Setting

Factory Default

Threshold

2026

TEACH Selection

Two-Point TEACH

Response Speed

Standard - 500 us

Offset Percent

10%

Auto Thresholds

OFF

OFF Delay

0 (Disabled)

OFF One-Shot

0 (Disabled)

ON Delay

0 (Disabled)

ON One-Shot

0 (Disabled)

Display Readout

Numeric, ECO
disabled, Normal
Orientation

Gain Selection

Auto Gain

Environmental Rating

IEC IP50, NEMA 1

Operating Conditions

Temperature: -10° to +55° C (+14° to 131° F)
Storage: -20° to +85° C (-4° to +185° F)
Relative Humidity: 90% @ 60° C (non-condensing)

Certifications

 

 

DF-G1 - Expert Dual Display Fiber Amplifier Manual

20

www.bannerengineering.com - tel: 763-544-3164

P/N 161999 Rev. A

Summary of Contents for DF-G1 Expert




























Reviews:

No comments

Brands by name

Popular brands

Load more brands