Banner DF-G1 Expert Manual Download | Manualshive

Page: 17 / 27

background image

For Sales and Support, Contact Walker EMD • Toll-free: (800) 876-4444 • Tel: (203) 426-7700 • Fax: (203) 426-7800 • www.walkeremd.com

Calibration SET

• Sets a threshold exactly at the presented condition
• Threshold can be adjusted using “+” and “-” rocker button (Manual Adjust)

A single sensing condition is presented, and the sensor positions a threshold exactly at the presented condition. When a condition lighter
than the threshold is sensed, the output either turns ON or OFF, depending on the LO/DO switch setting (see LO/DO Switch in

Panel Interface

on page 2).

Sensor positions

threshold exactly at

the presented condition

Threshold position

adjusted by

Manual Adjust

Darkest

(no signal)

Most Light

(saturated

signal)

Output OFF

Output ON

Condition

Presented

Figure 11. Calibration SET (Light Operate shown)

Calibration SET and Manual Adjust

• Moves switching threshold value up or down to make adjustments
• Slide Mode switch to ADJ to enter Adjust mode
• Press “+” to increase; press “-” to decrease

• GREEN display shows the switching threshold value
• 2 seconds after adjustment, the GREEN display will flash 3 times to confirm

• Slide Mode switch to RUN to complete operation

Remember: Auto Thresholding is automatically disabled in Calibration SET

DF-G1 - Expert Dual Display Fiber Amplifier Manual

P/N 161999 Rev. A

www.bannerengineering.com - tel: 763-544-3164

17

«
...
15
16
17
18
19
...
»

Summary of Contents for DF-G1 Expert




























Reviews:

No comments

Related manuals for DF-G1 Expert

Brand: omnicharge Pages: 12

Brand: omnicharge Pages: 72

Brand: Panasonic Pages: 116

Toughbook CF-T7BWATAAM

Brand: Panasonic Pages: 12

Brand: Barco Pages: 2

Brand: Barco Pages: 22

Brand: F&F Pages: 8

Brand: Oben Pages: 12

Brand: OBH Nordica Pages: 20

Brand: Olympus Pages: 2

Brand: Zagg Pages: 2

Canon C100 Z-Finder

Brand: Zacuto Pages: 14

Brand: Carax Pages: 2

Brand: GOgroove Pages: 9

Brand: Mahindra Pages: 25

IMI SENSORS EX640B61

Brand: PCB Piezotronics Pages: 70

Brand: Heitronic Pages: 12

Brand: Exact solutions Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands