Bandit SG-40, Operating & Parts Manual

Page: 9 / 92

Bandit
7
MODEL SG-40 SAFETY PROCEDURES
SAFETY PROCEDURES
YOUR SAFETY IS VERY IMPORTANT TO US!
Before starting the machine, take a minute to
check a few things. The machine should be in an
area restricted from people passing by. This area
around the machine must be free of all objects that
can obstruct your movement when working with the
machine. The machine should be checked for loose
tools or foreign objects. All tools not in use should
be secured in a tool box.
Operators
must at all times be located within easy
reach­of­all­control­and­shut-off­devices­when­the­unit­
is running. They must be attentive and prepared to
activate the devices.
Torn or loose clothing is more likely to get caught
in moving machinery parts. Keep such items as long
hair, shirt sleeves, and shirt tails properly contained.
Avoid wearing necklaces, rings, watches, and
especially neckties while operating this machinery.
This machine is equipped with safety decals,
guards and designs for your protection.
There must be at least two qualified and
trained operators at the work site. They must be
positioned in safe working locations, following safety
procedures and instructions, and aware of each
others whereabouts. There must, also, be at least
two people on site during maintenance and service
procedures in case an accident should occur.
This equipment is intended for use by adults
who have been properly trained and are physically
capable of operating the machine safely. Never
allow minors to operate this machine. Never operate
any­­machine­while­under­the­influence­of­drugs­or­
alcohol. Never operate equipment that is in need of
repair or adjustment. Keep children, bystanders and
animals clear of working area.
Accidents are typically caused by making
mistakes. The operator does not read the manual,
overlooks safety decals, or fails to use lockouts
provided for their safety. This occurs after the
operator has become familiar with the machine.
The operator is very cautious in the initial start up
and operation because they do not understand the
machine.
Before operating the machine, you must have all
potential operators read and follow manuals and
decals, watch the video and follow the guidelines.
Read and follow all the instructions in this
manual thoroughly. Your safety is dependent on
your knowledge of how to operate and maintain this
machine. You may obtain additional copies of this
manual from your Bandit Dealer.
Always be cautious and careful when operating
your equipment.
DANGER
NOTICE
Wear all personal protection equipment (PPE)
and follow all safety standards per ANSI and OSHA
instructions. Examples of equipment: hard hat,
face shield, safety glasses, gloves, ear protection,
high visibility vest, and steel toe boots. Do not wear
­gauntlet­or­secured­fit­gloves.­Always­keep­a­fully­
charged­ fire­ extinguisher­ with­ the­ machine­ while­
operating or servicing the machine. Failure to do
this will cause severe injury or death.
WARNING
DANGER
Never sit, stand, lay, climb or ride anywhere on this
machine while it is running, operating, or in transit.
You will be injured.
Do not operate this machine indoors. Exhaust
fumes can be fatal.
Never refuel while the machine is running. Never
refuel in the shop or building. Always refuel in a well
ventilated­area,­away­from­sparks­or­open­flames.­
Do not smoke while refueling. Extinguish all smoking
materials. Wipe up all spilled fuel before restarting
the engine.
Do not start the engine with the clutch or
cutter wheel engaged. Any debris may become a
dangerous projectile. Contact with the rotating cutter
wheel will result in serious injury or death.
Avoid moving parts. Keep hands, feet, and clothing
away from power driven parts. Keep all guards and
shields in place and properly secured. Contact with
moving parts will result in severe injury or death.
Keep hands clear of all pinch points. Failure to do
this will result in serious injury or death.
Do not go near the rotating cutter wheel for any
reason. Do not go near the cutter wheel while the
engine is running or the cutter wheel is coasting to a
stop. Contact with a rotating cutter wheel will result
in severe injury or death.